From 0cb36494666e2090046095f5704d840205207aae Mon Sep 17 00:00:00 2001
From: Michael Lucas <mwlucas@FreeBSD.org>
Date: Wed, 11 May 2005 20:58:57 +0000
Subject: [PATCH] Whitespace fixes from last commit.

---
 en_US.ISO8859-1/books/faq/book.sgml | 48 ++++++++++++++++-------------
 1 file changed, 26 insertions(+), 22 deletions(-)

diff --git a/en_US.ISO8859-1/books/faq/book.sgml b/en_US.ISO8859-1/books/faq/book.sgml
index 614dbf1e9e..2872a66a37 100644
--- a/en_US.ISO8859-1/books/faq/book.sgml
+++ b/en_US.ISO8859-1/books/faq/book.sgml
@@ -2553,29 +2553,31 @@ disk            wd2     at wdc1 drive 1 # change from wd3 to wd2</programlisting
             only, it will be
             <devicename>/dev/ukbd0</devicename>.</para>
 
-          <para>If you want to use the USB keyboard in the console, you
-            have to explicitly tell the console driver to use the existing
-            USB keyboard. This can be done by running the following
-            command as a part of system initialization.</para>
+          <para>If you want to use the USB keyboard in the console,
+            you have to explicitly tell the console driver to use the
+            existing USB keyboard. This can be done by running the
+            following command as a part of system
+            initialization.</para>
 
           <screen>&prompt.root; <userinput>kbdcontrol -k /dev/kbd1 &lt; /dev/ttyv0 &gt; /dev/null</userinput></screen>
 
-          <para>Note that if the USB keyboard is the only keyboard, it is
-            accessed as <devicename>/dev/kbd0</devicename>, thus, the command
-            should look like:</para>
+          <para>Note that if the USB keyboard is the only keyboard, it
+            is accessed as <devicename>/dev/kbd0</devicename>, thus,
+            the command should look like:</para>
 
           <screen>&prompt.root; <userinput>kbdcontrol -k /dev/kbd0 &lt; /dev/ttyv0 &gt; /dev/null</userinput></screen>
 
-          <para><filename>/etc/rc.i386</filename> is a good place to add the
-            above command.</para>
+          <para><filename>/etc/rc.i386</filename> is a good place to
+            add the above command.</para>
 
-          <para>Once this is done, the USB keyboard should work in the X
-            environment as well without any special settings.</para>
+          <para>Once this is done, the USB keyboard should work in the
+            X environment as well without any special settings.</para>
 
-          <para>Hot-plugging and unplugging of the USB keyboard may not
-            work quite right yet. We recommend connecting the keyboard
-            before starting the system and leaving it connected until the
-            system is shutdown to avoid troubles.</para>
+          <para>Hot-plugging and unplugging of the USB keyboard may
+            not work quite right yet. We recommend connecting the
+            keyboard before starting the system and leaving it
+            connected until the system is shutdown to avoid
+            troubles.</para>
 
           <para>See the &man.ukbd.4; manual page for more information.</para>
         </answer>
@@ -2583,7 +2585,8 @@ disk            wd2     at wdc1 drive 1 # change from wd3 to wd2</programlisting
 
       <qandaentry>
         <question id="busmouse">
-          <para>I have an unusual bus mouse. How do I set it up?</para>
+          <para>I have an unusual bus mouse. How do I set it
+            up?</para>
         </question>
 
         <answer>
@@ -2597,9 +2600,10 @@ disk            wd2     at wdc1 drive 1 # change from wd3 to wd2</programlisting
           <programlisting>device mse0 at isa? port 0x23c irq5</programlisting>
 
           <para>Bus mice usually come with dedicated interface cards.
-            These cards may allow you to set the port address and the IRQ
-            number other than shown above. Refer to the manual of your
-            mouse and the &man.mse.4; manual page for more information.</para>
+            These cards may allow you to set the port address and the
+            IRQ number other than shown above. Refer to the manual of
+            your mouse and the &man.mse.4; manual page for more
+            information.</para>
         </answer>
       </qandaentry>
 
@@ -2612,11 +2616,11 @@ disk            wd2     at wdc1 drive 1 # change from wd3 to wd2</programlisting
         <answer>
           <para>The PS/2 mouse is supported out-of-the-box.  The
              necessary device driver, <devicename>psm</devicename>, is
-             included in the GENERIC kernel.</para>
+             included in the kernel.</para>
 
           <para>If your custom kernel does not have this, add the
-            following line to your kernel configuration
-            and compile a new kernel.</para>
+            following line to your kernel configuration and compile a
+            new kernel.</para>
 
           <programlisting>device psm0 at atkbdc? irq 12</programlisting>