Add two spaces at the start of a sentence where needed.

This is a whitespace change that translators can ignore.

Obtained from:	    igor -n invocation
This commit is contained in:
Benedict Reuschling 2014-12-03 17:16:21 +00:00
parent 9440ff7930
commit 3bea668d72
Notes: svn2git 2020-12-08 03:00:23 +00:00
svn path=/head/; revision=46058
3 changed files with 7 additions and 7 deletions
en_US.ISO8859-1/books/handbook
firewalls
ppp-and-slip
x11

View file

@ -2313,7 +2313,7 @@ good_tcpo="22,25,37,53,80,443,110"</programlisting>
<para>On the inbound side, the ruleset has to deny bad packets <para>On the inbound side, the ruleset has to deny bad packets
and allow only authorized services. A packet which matches an and allow only authorized services. A packet which matches an
inbound rule is posted to the dynamic state table and the inbound rule is posted to the dynamic state table and the
packet is released to the <acronym>LAN</acronym>. The packet packet is released to the <acronym>LAN</acronym>. The packet
generated as a response is recognized by the generated as a response is recognized by the
<literal>check-state</literal> rule as belonging to an <literal>check-state</literal> rule as belonging to an
existing session. It is then sent to rule existing session. It is then sent to rule

View file

@ -216,7 +216,7 @@
<para>In order to configure a <acronym>PPP</acronym> connection, <para>In order to configure a <acronym>PPP</acronym> connection,
first edit <filename>/etc/ppp/ppp.conf</filename> with the first edit <filename>/etc/ppp/ppp.conf</filename> with the
dial-in information for the <acronym>ISP</acronym>. This file dial-in information for the <acronym>ISP</acronym>. This file
is described as follows:</para> is described as follows:</para>
<programlisting>1 default: <programlisting>1 default:
@ -818,7 +818,7 @@ set nbns 203.14.100.5</programlisting>
<programlisting>nat enable yes</programlisting> <programlisting>nat enable yes</programlisting>
<para>Alternatively, NAT may be enabled by command-line <para>Alternatively, NAT may be enabled by command-line
option <literal>-nat</literal>. There is also option <literal>-nat</literal>. There is also
<filename>/etc/rc.conf</filename> knob named <filename>/etc/rc.conf</filename> knob named
<literal>ppp_nat</literal>, which is enabled by <literal>ppp_nat</literal>, which is enabled by
default.</para> default.</para>
@ -1511,8 +1511,8 @@ ppp_profile="adsl"</programlisting>
configure <application>mpd</application> is available in HTML configure <application>mpd</application> is available in HTML
format in <filename>/usr/ports/share/doc/mpd/</filename>. format in <filename>/usr/ports/share/doc/mpd/</filename>.
Here is a sample configuration for connecting to an ADSL Here is a sample configuration for connecting to an ADSL
service with <application>mpd</application>. The configuration service with <application>mpd</application>. The
is spread over two files, first the configuration is spread over two files, first the
<filename>mpd.conf</filename>:</para> <filename>mpd.conf</filename>:</para>
<note> <note>
@ -1641,7 +1641,7 @@ ng0: flags=88d1&lt;UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,MULTICAST&gt; mtu 1500
session to the DSL router. Ethernet DSL modems have a session to the DSL router. Ethernet DSL modems have a
preconfigured LAN <acronym>IP</acronym> address to connect to. preconfigured LAN <acronym>IP</acronym> address to connect to.
In the case of the Alcatel &speedtouch; Home, this address is In the case of the Alcatel &speedtouch; Home, this address is
<systemitem class="ipaddress">10.0.0.138</systemitem>. The <systemitem class="ipaddress">10.0.0.138</systemitem>. The
router's documentation should list the address the device router's documentation should list the address the device
uses. To open the tunnel and start a <acronym>PPP</acronym> uses. To open the tunnel and start a <acronym>PPP</acronym>
session:</para> session:</para>

View file

@ -516,7 +516,7 @@ dbus_enable="YES"</programlisting>
</note> </note>
<para>If the test is unsuccessful, skip ahead to <xref <para>If the test is unsuccessful, skip ahead to <xref
linkend="x11-understanding"/>. Once the test is successful, linkend="x11-understanding"/>. Once the test is successful,
copy the configuration file to copy the configuration file to
<filename>/etc/X11/xorg.conf</filename>:</para> <filename>/etc/X11/xorg.conf</filename>:</para>