os/doc
3
0
Fork 0
Code Issues Pull requests Projects Releases Wiki Activity

Replace all contractions with their expanded form.

Browse source 
Approved by:	nik
This commit is contained in:
Giorgos Keramidas 2001-10-16 13:20:14 +00:00
parent b15029d064
commit 49731ee7b9
Notes: svn2git 2020-12-08 03:00:23 +00:00 
svn path=/head/; revision=10957
1 changed files with 8 additions and 8 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

16
en_US.ISO8859-1/articles/zip-drive/article.sgml
View file

@ -60,11 +60,11 @@
<para>If you want maximum performance and easy setup, the SCSI
interface is the best choice. This will probably require adding a
SCSI host adapter, since most PC's (except for high-performance
servers) don't have built-in SCSI support. Each SCSI host adapter
servers) do not have built-in SCSI support. Each SCSI host adapter
can support either 7 or 15 SCSI devices, depending on the
model.</para>
<para>Each SCSI device has it's own controller, and these
<para>Each SCSI device has its own controller, and these
controllers are fairly intelligent and well standardized, (the
second `S' in SCSI is for Standard) so from the operating system's
point of view, all SCSI disk drives look about the same, as do all
@ -73,7 +73,7 @@
a generic driver for each type of device, i.e. a SCSI disk driver,
SCSI tape driver, and so on. There are some SCSI devices that can
be better utilized with specialized drivers (e.g. DAT tape drives),
but they tend to work OK with the generic driver, too. It's just
but they tend to work OK with the generic driver, too. It is just
that the generic drivers may not support some of the special
features.</para>
@ -81,7 +81,7 @@
device file in the <filename>/dev</filename> directory represents
the ZIP drive. This can be determined by looking at the boot
messages while FreeBSD is booting (or in
<filename>/var/log/messages</filename> after booting), where you'll
<filename>/var/log/messages</filename> after booting), where you will
see a line something like this:</para>
<programlisting>da1: &lt;IOMEGA ZIP 100 D.13&gt; Removable Direct Access SCSI-2 Device</programlisting>
@ -167,7 +167,7 @@
uses IRQ 5 and address 378. Only the IRQ is required in the config
file.</para>
<para>If you're root hard disk is a SCSI disk, you might run into a
<para>If your root hard disk is a SCSI disk, you might run into a
problem with probing order, which will cause the system to attempt
to use the ZIP drive as the root device. This will cause a boot
failure, unless you happen to have a FreeBSD root file-system on
@ -195,7 +195,7 @@
<programlisting>controller scbus0 at aha0</programlisting></para>
<para>Lastly, as long as you're editing the kernel config, you
<para>Lastly, as long as you are editing the kernel config, you
can take the opportunity to remove all the unnecessary drivers. This
should be done with a great deal of caution, and only if you feel
confident about making kernel modifications. Removing unnecessary
@ -209,7 +209,7 @@
</listitem>
<listitem>
<para>Now it's time to compile the kernel:</para>
<para>Now it is time to compile the kernel:</para>
<screen>&prompt.root; <userinput>/usr/sbin/config MYKERNEL</userinput>
&prompt.root; <userinput>cd ../../compile/MYKERNEL</userinput>
@ -217,7 +217,7 @@
</listitem>
</orderedlist>
<para>After the kernel is rebuilt, you'll need to reboot. Make sure the
<para>After the kernel is rebuilt, you will need to reboot. Make sure the
ZIP drive is connected to the parallel port before the boot begins. You
should see the ZIP drive show up in the boot messages as device vpo0 or
vpo1, depending on which parallel port the drive is attached to. It