Minor cleanup of ancient devices which it's very unlikely anyone cares

about (and if they do the Hardware Notes are the relevant place to
look).

- Remove section about Jaz and Zip drives.
- Remove list of ancient CD-ROM drives.

en_US.ISO8859-1/books/faq/book.sgml

@@ -2356,41 +2356,8 @@
 
 	  <answer>
 	    <para>Any SCSI drive connected to a supported controller is
+	      supported.  Most ATAPI compatible IDE CD-ROMs are
 	      supported.</para>
-
-	    <para>The following proprietary CD-ROM interfaces are also
-	      supported:</para>
-
-	    <itemizedlist>
-	      <listitem>
-		<para>Mitsumi LU002 (8-bit), LU005 (16-bit) and FX001D
-		  (16-bit 2x Speed).</para>
-	      </listitem>
-
-	      <listitem>
-		<para>Sony CDU 31/33A</para>
-	      </listitem>
-
-	      <listitem>
-		<para>Sound Blaster Non-SCSI CD-ROM</para>
-	      </listitem>
-
-	      <listitem>
-		<para>Matsushita/Panasonic CD-ROM</para>
-	      </listitem>
-
-	      <listitem>
-		<para>ATAPI compatible IDE CD-ROMs</para>
-	      </listitem>
-	    </itemizedlist>
-
-	    <para>All non-SCSI cards are known to be extremely slow
-	      compared to SCSI drives, and some ATAPI CD-ROMs may not
-	      work.</para>
-
-	    <para>The official &os; CD-ROM ISO, and CD-ROMs from Daemon
-	      News and &os; Mall, support booting directly from the
-	      CD.</para>
 	  </answer>
 	</qandaentry>
 
@@ -2410,66 +2377,6 @@
 	      your kernel.</para>
 	  </answer>
 	</qandaentry>
-
-	<qandaentry>
-	  <question id="zip-support">
-	    <para>Does &os; support &iomegazip; drives?</para>
-	  </question>
-
-	  <answer>
-	    <para>&os; supports SCSI and ATAPI (IDE) &iomegazip; drives
-	      out of the box.  SCSI ZIP drives can only be set to run at
-	      SCSI target IDs 5 or 6, but if your SCSI host adapter's
-	      BIOS supports it you can even boot from it.  It is not
-	      clear which host adapters support booting from targets
-	      other than 0 or 1, so you will have to consult your
-	      adapter's documentation if you would like to use this
-	      feature.</para>
-
-	    <para>&os; also supports Parallel Port Zip Drives.  Check
-	      that your kernel contains the
-	      <devicename>scbus0</devicename>,
-	      <devicename>da0</devicename>,
-	      <devicename>ppbus0</devicename>, and
-	      <devicename>vp0</devicename> drivers (the
-	      <filename>GENERIC</filename> kernel contains everything
-	      except <devicename>vp0</devicename>).  With all these
-	      drivers present, the Parallel Port drive should be available
-	      as <devicename>/dev/da0s4</devicename>.  Disks can be
-	      mounted using <command>mount /dev/da0s4 /mnt</command> OR
-	      (for DOS disks) <command>mount -t msdosfs /dev/da0s4 /mnt</command>
-	      as appropriate.</para>
-
-	    <para>Also check out <link linkend="media-change">the FAQ on
-	      removable drives</link> later in this chapter, and <link
-		linkend="removable-drives">the note on
-	      <quote>formatting</quote></link>in the Administration
-	      chapter.</para>
-	  </answer>
-	</qandaentry>
-
-	<qandaentry>
-	  <question id="jaz-zip-removable-support">
-	    <para>Does &os; support &jaz;, EZ and other removable
-	      drives?</para>
-	  </question>
-
-	  <answer>
-	    <para>They work.  Most of these are SCSI devices, so they
-	      look like SCSI disks to &os;.  The IDE EZ looks like an IDE
-	      drive.</para>
-
-	    <para>Make sure that any external units are powered on when
-	      booting the system.</para>
-
-	    <para><anchor id="media-change">To change the media while
-	      running, check out &man.mount.8;, &man.umount.8;, and
-	      &man.camcontrol.8; (for SCSI devices) or &man.atacontrol.8;
-	      (for IDE devices), plus the <link
-		linkend="removable-drives">discussion on using removable drives</link>
-	      later in the FAQ.</para>
-	  </answer>
-	</qandaentry>
       </qandaset>
     </sect1>