From f7064c07e3f9dda50facdf3e804ed465d1060717 Mon Sep 17 00:00:00 2001
From: Benedict Reuschling <bcr@FreeBSD.org>
Date: Wed, 7 Jul 2010 21:09:09 +0000
Subject: [PATCH] Add more s/FreeBSD/&os; replacements to the article where
possible.
Approved by: jkois (mentor)
---
.../articles/solid-state/article.sgml | 20 +++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/en_US.ISO8859-1/articles/solid-state/article.sgml b/en_US.ISO8859-1/articles/solid-state/article.sgml
index a50abe521e..d9b93068f0 100644
--- a/en_US.ISO8859-1/articles/solid-state/article.sgml
+++ b/en_US.ISO8859-1/articles/solid-state/article.sgml
@@ -38,7 +38,7 @@
<article>
<articleinfo>
- <title>FreeBSD and Solid State Devices</title>
+ <title>&os; and Solid State Devices</title>
<authorgroup>
<author>
@@ -67,7 +67,7 @@
&legalnotice;
<abstract>
- <para>This article covers the use of solid state disk devices in FreeBSD
+ <para>This article covers the use of solid state disk devices in &os;
to create embedded systems.</para>
<para>Embedded systems have the advantage of increased stability due to
@@ -114,7 +114,7 @@
to the IDE bus and are compatible with the ATA command set. Therefore,
with a very simple and low-cost adaptor, these devices can be attached
directly to an IDE bus in a computer. Once implemented in this manner,
- operating systems such as FreeBSD see the device as a normal hard disk
+ operating systems such as &os; see the device as a normal hard disk
(albeit small).</para>
<para>Other solid state disk solutions do exist, but their expense,
@@ -136,7 +136,7 @@
<filename>/tmp</filename> and <filename>/var</filename> are mounted as
memory filesystems to allow the system to create logs and update
counters and temporary files. Memory filesystems are a critical
- component to a successful solid state FreeBSD implementation.</para>
+ component to a successful solid state &os; implementation.</para>
<para>You should make sure the following lines exist in your kernel
configuration file:</para>
@@ -210,12 +210,12 @@ pseudo-device md # memory disk</programlisting>
<sect1>
<title>Building a File System From Scratch</title>
- <para>Because ATA compatible compact-flash cards are seen by FreeBSD as
+ <para>Because ATA compatible compact-flash cards are seen by &os; as
normal IDE hard drives, you could
- theoretically install FreeBSD from the network using the kern and
+ theoretically install &os; from the network using the kern and
mfsroot floppies or from a CD.</para>
- <para>However, even a small installation of FreeBSD using normal
+ <para>However, even a small installation of &os; using normal
installation procedures can produce a system in size of greater than 200
megabytes. Because most people will be using smaller flash memory
devices (128 megabytes is considered fairly large - 32 or even 16
@@ -224,7 +224,7 @@ pseudo-device md # memory disk</programlisting>
smallest of conventional installations.</para>
<para>The easiest way to overcome this space limitation is to install
- FreeBSD using conventional means to a normal hard disk. After the
+ &os; using conventional means to a normal hard disk. After the
installation is complete, pare down the operating system to a size that
will fit onto your flash media, then tar the entire filesystem. The
following steps will guide you through the process of preparing a piece
@@ -249,7 +249,7 @@ pseudo-device md # memory disk</programlisting>
<literal>165</literal>. Now write this partition table to the disk
by pressing the <keycap>w</keycap> key (this is a hidden option on
this screen). If you are using an ATA compatible compact
- flash card, you should choose the FreeBSD Boot Manager. Now press
+ flash card, you should choose the &os; Boot Manager. Now press
the <keycap>q</keycap> key to quit the partition menu. You will be
shown the boot manager menu once more - repeat the choice you made
earlier.</para>
@@ -324,7 +324,7 @@ pseudo-device md # memory disk</programlisting>
<para>Assuming that you configured your filesystem correctly when it
was built on the normal hard disk (with your filesystems mounted
read-only, and with the necessary options compiled into the kernel)
- you should now be successfully booting your FreeBSD embedded
+ you should now be successfully booting your &os; embedded
system.</para>
</step>
</procedure>