eb2cd84505
informaltable element properly, unless the pgwide attribute is explicitly set to 1. Use this consistently within the (en) tree, and update the FDP accordingly. This should finally silence the demons in: PR: docs/73095 Submitted by: Hilko Meyer <Hilko dot Meyer at gmx dot de>
2643 lines
107 KiB
Text
2643 lines
107 KiB
Text
<!DOCTYPE article PUBLIC "-//FreeBSD//DTD DocBook V4.1-Based Extension//EN" [
|
|
<!ENTITY % articles.ent PUBLIC "-//FreeBSD//ENTITIES DocBook FreeBSD Articles Entity Set//EN">
|
|
%articles.ent;
|
|
]>
|
|
|
|
<article>
|
|
<articleinfo>
|
|
<title>Storage Devices</title>
|
|
|
|
<authorgroup>
|
|
<author>
|
|
<firstname>Wilko</firstname>
|
|
<surname>Bulte</surname>
|
|
|
|
<affiliation>
|
|
<address><email>wilko@FreeBSD.org</email></address>
|
|
</affiliation>
|
|
</author>
|
|
</authorgroup>
|
|
|
|
<pubdate>$FreeBSD$</pubdate>
|
|
|
|
|
|
<legalnotice id="trademarks" role="trademarks">
|
|
&tm-attrib.freebsd;
|
|
&tm-attrib.general;
|
|
</legalnotice>
|
|
|
|
<abstract>
|
|
<para>This article talks about storage devices with FreeBSD.</para>
|
|
</abstract>
|
|
</articleinfo>
|
|
|
|
<sect1 id="esdi">
|
|
<title>Using ESDI hard disks</title>
|
|
|
|
<para><emphasis>Copyright © 1995, &a.wilko;. 24 September
|
|
1995.</emphasis></para>
|
|
|
|
<para>ESDI is an acronym that means Enhanced Small Device
|
|
Interface. It is loosely based on the good old ST506/412
|
|
interface originally devised by Seagate Technology, the makers
|
|
of the first affordable 5.25" winchester disk.</para>
|
|
|
|
<para>The acronym says Enhanced, and rightly so. In the first
|
|
place the speed of the interface is higher, 10 or 15
|
|
Mbits/second instead of the 5 Mbits/second of ST412 interfaced
|
|
drives. Secondly some higher level commands are added, making
|
|
the ESDI interface somewhat <quote>smarter</quote> to the operating system
|
|
driver writers. It is by no means as smart as SCSI by the way.
|
|
ESDI is standardized by ANSI.</para>
|
|
|
|
<para>Capacities of the drives are boosted by putting more sectors
|
|
on each track. Typical is 35 sectors per track, high capacity
|
|
drives I have seen were up to 54 sectors/track.</para>
|
|
|
|
<para>Although ESDI has been largely obsoleted by IDE and SCSI
|
|
interfaces, the availability of free or cheap surplus drives
|
|
makes them ideal for low (or now) budget systems.</para>
|
|
|
|
<sect2>
|
|
<title>Concepts of ESDI</title>
|
|
|
|
<sect3>
|
|
<title>Physical connections</title>
|
|
|
|
<para>The ESDI interface uses two cables connected to each drive.
|
|
One cable is a 34 pin flat cable edge connector that carries the
|
|
command and status signals from the controller to the drive and
|
|
vice-versa. The command cable is daisy chained between all the
|
|
drives. So, it forms a bus onto which all drives are
|
|
connected.</para>
|
|
|
|
<para>The second cable is a 20 pin flat cable edge connector that
|
|
carries the data to and from the drive. This cable is radially
|
|
connected, so each drive has its own direct connection to the
|
|
controller.</para>
|
|
|
|
<para>To the best of my knowledge PC ESDI controllers are limited to
|
|
using a maximum of 2 drives per controller. This is compatibility
|
|
feature(?) left over from the WD1003 standard that reserves only a
|
|
single bit for device addressing.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Device addressing</title>
|
|
|
|
<para>On each command cable a maximum of 7 devices and 1 controller
|
|
can be present. To enable the controller to uniquely identify
|
|
which drive it addresses, each ESDI device is equipped with
|
|
jumpers or switches to select the devices address.</para>
|
|
|
|
<para>On PC type controllers the first drive is set to address 0,
|
|
the second disk to address 1. <emphasis>Always make
|
|
sure</emphasis> you set each disk to an unique address! So, on a
|
|
PC with its two drives/controller maximum the first drive is drive
|
|
0, the second is drive 1.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Termination</title>
|
|
|
|
<para>The daisy chained command cable (the 34 pin cable remember?)
|
|
needs to be terminated at the last drive on the chain. For this
|
|
purpose ESDI drives come with a termination resistor network that
|
|
can be removed or disabled by a jumper when it is not used.</para>
|
|
|
|
<para>So, one and <emphasis>only</emphasis> one drive, the one at
|
|
the farthest end of the command cable has its terminator
|
|
installed/enabled. The controller automatically terminates the
|
|
other end of the cable. Please note that this implies that the
|
|
controller must be at one end of the cable and
|
|
<emphasis>not</emphasis> in the middle.</para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Using ESDI disks with FreeBSD</title>
|
|
|
|
<para>Why is ESDI such a pain to get working in the first
|
|
place?</para>
|
|
|
|
<para>People who tried ESDI disks with FreeBSD are known to have
|
|
developed a profound sense of frustration. A combination of factors
|
|
works against you to produce effects that are hard to understand
|
|
when you have never seen them before.</para>
|
|
|
|
<para>This has also led to the popular legend ESDI and FreeBSD is a
|
|
plain NO-GO. The following sections try to list all the pitfalls
|
|
and solutions.</para>
|
|
|
|
<sect3>
|
|
<title>ESDI speed variants</title>
|
|
|
|
<para>As briefly mentioned before, ESDI comes in two speed flavors.
|
|
The older drives and controllers use a 10 Mbits/second data
|
|
transfer rate. Newer stuff uses 15 Mbits/second.</para>
|
|
|
|
<para>It is not hard to imagine that 15 Mbits/second drive cause
|
|
problems on controllers laid out for 10 Mbits/second. As always,
|
|
consult your controller <emphasis>and</emphasis> drive
|
|
documentation to see if things match.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Stay on track</title>
|
|
|
|
<para>Mainstream ESDI drives use 34 to 36 sectors per track. Most
|
|
(older) controllers cannot handle more than this number of
|
|
sectors. Newer, higher capacity, drives use higher numbers of
|
|
sectors per track. For instance, I own a 670 MB drive that has 54
|
|
sectors per track.</para>
|
|
|
|
<para>In my case, the controller could not handle this number of
|
|
sectors. It proved to work well except that it only used 35
|
|
sectors on each track. This meant losing a lot of disk
|
|
space.</para>
|
|
|
|
<para>Once again, check the documentation of your hardware for more
|
|
info. Going out-of-spec like in the example might or might not
|
|
work. Give it a try or get another more capable
|
|
controller.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Hard or soft sectoring</title>
|
|
|
|
<para>Most ESDI drives allow hard or soft sectoring to be selected
|
|
using a jumper. Hard sectoring means that the drive will produce
|
|
a sector pulse on the start of each new sector. The controller
|
|
uses this pulse to tell when it should start to write or
|
|
read.</para>
|
|
|
|
<para>Hard sectoring allows a selection of sector size (normally
|
|
256, 512 or 1024 bytes per formatted sector). FreeBSD uses 512
|
|
byte sectors. The number of sectors per track also varies while
|
|
still using the same number of bytes per formatted sector. The
|
|
number of <emphasis>unformatted</emphasis> bytes per sector
|
|
varies, dependent on your controller it needs more or less
|
|
overhead bytes to work correctly. Pushing more sectors on a
|
|
track of course gives you more usable space, but might give
|
|
problems if your controller needs more bytes than the drive
|
|
offers.</para>
|
|
|
|
<para>In case of soft sectoring, the controller itself determines
|
|
where to start/stop reading or writing. For ESDI hard sectoring
|
|
is the default (at least on everything I came across). I never
|
|
felt the urge to try soft sectoring.</para>
|
|
|
|
<para>In general, experiment with sector settings before you install
|
|
FreeBSD because you need to re-run the low-level format after each
|
|
change.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Low level formatting</title>
|
|
|
|
<para>ESDI drives need to be low level formatted before they are
|
|
usable. A reformat is needed whenever you figgle with the number
|
|
of sectors/track jumpers or the physical orientation of the drive
|
|
(horizontal, vertical). So, first think, then format. The format
|
|
time must not be underestimated, for big disks it can take
|
|
hours.</para>
|
|
|
|
<para>After a low level format, a surface scan is done to find and
|
|
flag bad sectors. Most disks have a manufacturer bad block list
|
|
listed on a piece of paper or adhesive sticker. In addition, on
|
|
most disks the list is also written onto the disk. Please use the
|
|
manufacturer's list. It is much easier to remap a defect now than
|
|
after FreeBSD is installed.</para>
|
|
|
|
<para>Stay away from low-level formatters that mark all sectors of a
|
|
track as bad as soon as they find one bad sector. Not only does
|
|
this waste space, it also and more importantly causes you grief
|
|
with bad144 (see the section on bad144).</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Translations</title>
|
|
|
|
<para>Translations, although not exclusively a ESDI-only problem,
|
|
might give you real trouble. Translations come in multiple
|
|
flavors. Most of them have in common that they attempt to work
|
|
around the limitations posed upon disk geometries by the original
|
|
IBM PC/AT design (thanks IBM!).</para>
|
|
|
|
<para>First of all there is the (in)famous 1024 cylinder limit. For
|
|
a system to be able to boot, the stuff (whatever operating system)
|
|
must be in the first 1024 cylinders of a disk. Only 10 bits are
|
|
available to encode the cylinder number. For the number of
|
|
sectors the limit is 64 (0-63). When you combine the 1024
|
|
cylinder limit with the 16 head limit (also a design feature) you
|
|
max out at fairly limited disk sizes.</para>
|
|
|
|
<para>To work around this problem, the manufacturers of ESDI PC
|
|
controllers added a BIOS prom extension on their boards. This
|
|
BIOS extension handles disk I/O for booting (and for some
|
|
operating systems <emphasis>all</emphasis> disk I/O) by using
|
|
translation. For instance, a big drive might be presented to the
|
|
system as having 32 heads and 64 sectors/track. The result is
|
|
that the number of cylinders is reduced to something below 1024
|
|
and is therefore usable by the system without problems. It is
|
|
noteworthy to know that FreeBSD does not use the BIOS after its
|
|
kernel has started. More on this later.</para>
|
|
|
|
<para>A second reason for translations is the fact that most older
|
|
system BIOSes could only handle drives with 17 sectors per track
|
|
(the old ST412 standard). Newer system BIOSes usually have a
|
|
user-defined drive type (in most cases this is drive type
|
|
47).</para>
|
|
|
|
<warning>
|
|
<para>Whatever you do to translations after reading this document,
|
|
keep in mind that if you have multiple operating systems on the
|
|
same disk, all must use the same translation</para>
|
|
</warning>
|
|
|
|
<para>While on the subject of translations, I have seen one
|
|
controller type (but there are probably more like this) offer the
|
|
option to logically split a drive in multiple partitions as a BIOS
|
|
option. I had select 1 drive == 1 partition because this
|
|
controller wrote this info onto the disk. On power-up it read the
|
|
info and presented itself to the system based on the info from the
|
|
disk.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Spare sectoring</title>
|
|
|
|
<para>Most ESDI controllers offer the possibility to remap bad
|
|
sectors. During/after the low-level format of the disk bad
|
|
sectors are marked as such, and a replacement sector is put in
|
|
place (logically of course) of the bad one.</para>
|
|
|
|
<para>In most cases the remapping is done by using N-1 sectors on
|
|
each track for actual data storage, and sector N itself is the
|
|
spare sector. N is the total number of sectors physically
|
|
available on the track. The idea behind this is that the
|
|
operating system sees a <quote>perfect</quote> disk without bad sectors. In
|
|
the case of FreeBSD this concept is not usable.</para>
|
|
|
|
<para>The problem is that the translation from
|
|
<emphasis>bad</emphasis> to <emphasis>good</emphasis> is performed
|
|
by the BIOS of the ESDI controller. FreeBSD, being a true 32 bit
|
|
operating system, does not use the BIOS after it has been booted.
|
|
Instead, it has device drivers that talk directly to the
|
|
hardware.</para>
|
|
|
|
<para><emphasis>So: do not use spare sectoring, bad block remapping
|
|
or whatever it may be called by the controller manufacturer when
|
|
you want to use the disk for FreeBSD.</emphasis></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Bad block handling</title>
|
|
|
|
<para>The preceding section leaves us with a problem. The
|
|
controller's bad block handling is not usable and still FreeBSD's
|
|
filesystems assume perfect media without any flaws. To solve this
|
|
problem, FreeBSD use the <command>bad144</command> tool. Bad144
|
|
(named after a Digital Equipment standard for bad block handling)
|
|
scans a FreeBSD slice for bad blocks. Having found these bad
|
|
blocks, it writes a table with the offending block numbers to the
|
|
end of the FreeBSD slice.</para>
|
|
|
|
<para>When the disk is in operation, the disk accesses are checked
|
|
against the table read from the disk. Whenever a block number is
|
|
requested that is in the <command>bad144</command> list, a
|
|
replacement block (also from the end of the FreeBSD slice) is
|
|
used. In this way, the <command>bad144</command> replacement
|
|
scheme presents <quote>perfect</quote> media to the FreeBSD filesystems.</para>
|
|
|
|
<para>There are a number of potential pitfalls associated with the
|
|
use of <command>bad144</command>. First of all, the slice cannot
|
|
have more than 126 bad sectors. If your drive has a high number
|
|
of bad sectors, you might need to divide it into multiple FreeBSD
|
|
slices each containing less than 126 bad sectors. Stay away from
|
|
low-level format programs that mark <emphasis>every</emphasis>
|
|
sector of a track as bad when they find a flaw on the track. As
|
|
you can imagine, the 126 limit is quickly reached when the
|
|
low-level format is done this way.</para>
|
|
|
|
<para>Second, if the slice contains the root filesystem, the slice
|
|
should be within the 1024 cylinder BIOS limit. During the boot
|
|
process the bad144 list is read using the BIOS and this only
|
|
succeeds when the list is within the 1024 cylinder limit.</para>
|
|
|
|
<note>
|
|
<para>The restriction is not that only the root
|
|
<emphasis>filesystem</emphasis> must be within the 1024 cylinder
|
|
limit, but rather the entire <emphasis>slice</emphasis> that
|
|
contains the root filesystem.</para>
|
|
</note>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Kernel configuration</title>
|
|
|
|
<para>ESDI disks are handled by the same <literal>wd</literal>driver
|
|
as IDE and ST412 MFM disks. The <literal>wd</literal> driver
|
|
should work for all WD1003 compatible interfaces.</para>
|
|
|
|
<para>Most hardware is jumperable for one of two different I/O
|
|
address ranges and IRQ lines. This allows you to have two wd
|
|
type controllers in one system.</para>
|
|
|
|
<para>When your hardware allows non-standard strappings, you can use
|
|
these with FreeBSD as long as you enter the correct info into the
|
|
kernel config file. An example from the kernel config file (they
|
|
live in <filename>/sys/i386/conf</filename> BTW).</para>
|
|
|
|
<programlisting># First WD compatible controller
|
|
controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr
|
|
disk wd0 at wdc0 drive 0
|
|
disk wd1 at wdc0 drive 1
|
|
# Second WD compatible controller
|
|
controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr
|
|
disk wd2 at wdc1 drive 0
|
|
disk wd3 at wdc1 drive 1</programlisting>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Particulars on ESDI hardware</title>
|
|
|
|
<sect3>
|
|
<title>Adaptec 2320 controllers</title>
|
|
|
|
<para>I successfully installed FreeBSD onto a ESDI disk controlled
|
|
by a ACB-2320. No other operating system was present on the
|
|
disk.</para>
|
|
|
|
<para>To do so I low level formatted the disk using
|
|
<command>NEFMT.EXE</command> (<command>ftp</command>able from
|
|
<hostid role="fqdn">www.adaptec.com</hostid>) and answered NO to
|
|
the question whether the disk should be formatted with a spare
|
|
sector on each track. The BIOS on the ACD-2320 was disabled. I
|
|
used the <literal>free configurable</literal> option in the system
|
|
BIOS to allow the BIOS to boot it.</para>
|
|
|
|
<para>Before using <command>NEFMT.EXE</command> I tried to format
|
|
the disk using the ACB-2320 BIOS built-in formatter. This proved
|
|
to be a show stopper, because it did not give me an option to
|
|
disable spare sectoring. With spare sectoring enabled the FreeBSD
|
|
installation process broke down on the <command>bad144</command>
|
|
run.</para>
|
|
|
|
<para>Please check carefully which
|
|
ACB-232<replaceable>xy</replaceable> variant you have. The
|
|
<replaceable>x</replaceable> is either <literal>0</literal> or
|
|
<literal>2</literal>, indicating a controller without or with a
|
|
floppy controller on board.</para>
|
|
|
|
<para>The <literal>y</literal> is more interesting. It can either
|
|
be a blank, a <literal>A-8</literal> or a <literal>D</literal>. A
|
|
blank indicates a plain 10 Mbits/second controller. An
|
|
<literal>A-8</literal> indicates a 15 Mbits/second controller
|
|
capable of handling 52 sectors/track. A <literal>D</literal>
|
|
means a 15 Mbits/second controller that can also handle drives
|
|
with > 36 sectors/track (also 52?).</para>
|
|
|
|
<para>All variations should be capable of using 1:1 interleaving.
|
|
Use 1:1, FreeBSD is fast enough to handle it.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Western Digital WD1007 controllers</title>
|
|
|
|
<para>I successfully installed FreeBSD onto a ESDI disk controlled
|
|
by a WD1007 controller. To be precise, it was a WD1007-WA2.
|
|
Other variations of the WD1007 do exist.</para>
|
|
|
|
<para>To get it to work, I had to disable the sector translation and
|
|
the WD1007's onboard BIOS. This implied I could not use the
|
|
low-level formatter built into this BIOS. Instead, I grabbed
|
|
<command>WDFMT.EXE</command> from <hostid
|
|
role="fqdn">www.wdc.com</hostid> Running this formatted my drive
|
|
just fine.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Ultrastor U14F controllers</title>
|
|
|
|
<para>According to multiple reports from the net, Ultrastor ESDI
|
|
boards work OK with FreeBSD. I lack any further info on
|
|
particular settings.</para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2 id="esdi-further-reading">
|
|
<title>Further reading</title>
|
|
|
|
<para>If you intend to do some serious ESDI hacking, you might want to
|
|
have the official standard at hand:</para>
|
|
|
|
<para>The latest ANSI X3T10 committee document is: Enhanced Small
|
|
Device Interface (ESDI) [X3.170-1990/X3.170a-1991] [X3T10/792D
|
|
Rev 11]</para>
|
|
|
|
<para>On Usenet the newsgroup <ulink
|
|
url="news:comp.periphs">comp.periphs</ulink> is a noteworthy place
|
|
to look for more info.</para>
|
|
|
|
<para>The World Wide Web (WWW) also proves to be a very handy info
|
|
source: For info on Adaptec ESDI controllers see <ulink
|
|
url="http://www.adaptec.com/"></ulink>. For
|
|
info on Western Digital controllers see
|
|
<ulink url="http://www.wdc.com/"></ulink>.</para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Thanks to...</title>
|
|
|
|
<para>Andrew Gordon for sending me an Adaptec 2320 controller and ESDI
|
|
disk for testing.</para>
|
|
</sect2>
|
|
</sect1>
|
|
|
|
<sect1 id="scsi">
|
|
<title>What is SCSI?</title>
|
|
|
|
<para><emphasis>Copyright © 1995, &a.wilko;. July 6,
|
|
1996.</emphasis></para>
|
|
|
|
<para>SCSI is an acronym for Small Computer Systems Interface. It is an
|
|
ANSI standard that has become one of the leading I/O buses in the
|
|
computer industry. The foundation of the SCSI standard was laid by
|
|
Shugart Associates (the same guys that gave the world the first mini
|
|
floppy disks) when they introduced the SASI bus (Shugart Associates
|
|
Standard Interface).</para>
|
|
|
|
<para>After some time an industry effort was started to come to a more
|
|
strict standard allowing devices from different vendors to work
|
|
together. This effort was recognized in the ANSI SCSI-1 standard.
|
|
The SCSI-1 standard (approximately 1985) is rapidly becoming obsolete. The
|
|
current standard is SCSI-2 (see <link
|
|
linkend="scsi-further-reading">Further reading</link>), with SCSI-3
|
|
on the drawing boards.</para>
|
|
|
|
<para>In addition to a physical interconnection standard, SCSI defines a
|
|
logical (command set) standard to which disk devices must adhere.
|
|
This standard is called the Common Command Set (CCS) and was developed
|
|
more or less in parallel with ANSI SCSI-1. SCSI-2 includes the
|
|
(revised) CCS as part of the standard itself. The commands are
|
|
dependent on the type of device at hand. It does not make much sense
|
|
of course to define a Write command for a scanner.</para>
|
|
|
|
<para>The SCSI bus is a parallel bus, which comes in a number of
|
|
variants. The oldest and most used is an 8 bit wide bus, with
|
|
single-ended signals, carried on 50 wires. (If you do not know what
|
|
single-ended means, do not worry, that is what this document is all
|
|
about.) Modern designs also use 16 bit wide buses, with differential
|
|
signals. This allows transfer speeds of 20Mbytes/second, on cables
|
|
lengths of up to 25 meters. SCSI-2 allows a maximum bus width of 32
|
|
bits, using an additional cable. Quickly emerging are Ultra SCSI (also
|
|
called Fast-20) and Ultra2 (also called Fast-40). Fast-20 is 20
|
|
million transfers per second (20 Mbytes/sec on a 8 bit bus), Fast-40
|
|
is 40 million transfers per second (40 Mbytes/sec on a 8 bit bus).
|
|
Most hard drives sold today are single-ended Ultra SCSI (8 or 16
|
|
bits).</para>
|
|
|
|
<para>Of course the SCSI bus not only has data lines, but also a number
|
|
of control signals. A very elaborate protocol is part of the standard
|
|
to allow multiple devices to share the bus in an efficient manner. In
|
|
SCSI-2, the data is always checked using a separate parity line. In
|
|
pre-SCSI-2 designs parity was optional.</para>
|
|
|
|
<para>In SCSI-3 even faster bus types are introduced, along with a
|
|
serial SCSI busses that reduces the cabling overhead and allows a
|
|
higher maximum bus length. You might see names like SSA and
|
|
fibre channel in this context. None of the serial buses are currently
|
|
in widespread use (especially not in the typical FreeBSD environment).
|
|
For this reason the serial bus types are not discussed any
|
|
further.</para>
|
|
|
|
<para>As you could have guessed from the description above, SCSI devices
|
|
are intelligent. They have to be to adhere to the SCSI standard
|
|
(which is over 2 inches thick BTW). So, for a hard disk drive for
|
|
instance you do not specify a head/cylinder/sector to address a
|
|
particular block, but simply the number of the block you want.
|
|
Elaborate caching schemes, automatic bad block replacement etc are all
|
|
made possible by this <quote>intelligent device</quote> approach.</para>
|
|
|
|
<para>On a SCSI bus, each possible pair of devices can communicate.
|
|
Whether their function allows this is another matter, but the standard
|
|
does not restrict it. To avoid signal contention, the 2 devices have
|
|
to arbitrate for the bus before using it.</para>
|
|
|
|
<para>The philosophy of SCSI is to have a standard that allows
|
|
older-standard devices to work with newer-standard ones. So, an old
|
|
SCSI-1 device should normally work on a SCSI-2 bus. I say Normally,
|
|
because it is not absolutely sure that the implementation of an old
|
|
device follows the (old) standard closely enough to be acceptable on a
|
|
new bus. Modern devices are usually more well-behaved, because the
|
|
standardization has become more strict and is better adhered to by the
|
|
device manufacturers.</para>
|
|
|
|
<para>Generally speaking, the chances of getting a working set of
|
|
devices on a single bus is better when all the devices are SCSI-2 or
|
|
newer. This implies that you do not have to dump all your old stuff
|
|
when you get that shiny 80GB disk: I own a system on which a pre-SCSI-1
|
|
disk, a SCSI-2 QIC tape unit, a SCSI-1 helical scan tape unit and 2
|
|
SCSI-1 disks work together quite happily. From a performance
|
|
standpoint you might want to separate your older and newer (=faster)
|
|
devices however. This is especially advantageous if you have an
|
|
Ultra160 host adapter where you should separate your U160 devices
|
|
from the Fast and Wide SCSI-2 devices.</para>
|
|
|
|
<sect2>
|
|
<title>Components of SCSI</title>
|
|
|
|
<para>As said before, SCSI devices are smart. The idea is to put the
|
|
knowledge about intimate hardware details onto the SCSI device
|
|
itself. In this way, the host system does not have to worry about
|
|
things like how many heads a hard disks has, or how many tracks
|
|
there are on a specific tape device. If you are curious, the
|
|
standard specifies commands with which you can query your devices on
|
|
their hardware particulars. FreeBSD uses this capability during
|
|
boot to check out what devices are connected and whether they need
|
|
any special treatment.</para>
|
|
|
|
<para>The advantage of intelligent devices is obvious: the device
|
|
drivers on the host can be made in a much more generic fashion,
|
|
there is no longer a need to change (and qualify!) drivers for every
|
|
odd new device that is introduced.</para>
|
|
|
|
<para>For cabling and connectors there is a golden rule: get good
|
|
stuff. With bus speeds going up all the time you will save yourself
|
|
a lot of grief by using good material.</para>
|
|
|
|
<para>So, gold plated connectors, shielded cabling, sturdy connector
|
|
hoods with strain reliefs etc are the way to go. Second golden rule:
|
|
do no use cables longer than necessary. I once spent 3 days hunting
|
|
down a problem with a flaky machine only to discover that shortening
|
|
the SCSI bus by 1 meter solved the problem. And the original bus
|
|
length was well within the SCSI specification.</para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>SCSI bus types</title>
|
|
|
|
<para>From an electrical point of view, there are two incompatible bus
|
|
types: single-ended and differential. This means that there are two
|
|
different main groups of SCSI devices and controllers, which cannot
|
|
be mixed on the same bus. It is possible however to use special
|
|
converter hardware to transform a single-ended bus into a
|
|
differential one (and vice versa). The differences between the bus
|
|
types are explained in the next sections.</para>
|
|
|
|
<para>In lots of SCSI related documentation there is a sort of jargon
|
|
in use to abbreviate the different bus types. A small list:</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para>FWD: Fast Wide Differential</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>FND: Fast Narrow Differential</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>SE: Single Ended</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>FN: Fast Narrow</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>etc.</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
|
|
|
|
<para>With a minor amount of imagination one can usually imagine what
|
|
is meant.</para>
|
|
|
|
<para>Wide is a bit ambiguous, it can indicate 16 or 32 bit buses. As
|
|
far as I know, the 32 bit variant is not (yet) in use, so wide
|
|
normally means 16 bit.</para>
|
|
|
|
<para>Fast means that the timing on the bus is somewhat different, so
|
|
that on a narrow (8 bit) bus 10 Mbytes/sec are possible instead of 5
|
|
Mbytes/sec for <quote>slow</quote> SCSI. As discussed before, bus speeds of 20
|
|
and 40 million transfers/second are also emerging (Fast-20 == Ultra
|
|
SCSI and Fast-40 == Ultra2 SCSI).</para>
|
|
|
|
<note>
|
|
<para>The data lines > 8 are only used for data transfers and
|
|
device addressing. The transfers of commands and status messages
|
|
etc are only performed on the lowest 8 data lines. The standard
|
|
allows narrow devices to operate on a wide bus. The usable bus
|
|
width is negotiated between the devices. You have to watch your
|
|
device addressing closely when mixing wide and narrow.</para>
|
|
</note>
|
|
|
|
<sect3>
|
|
<title>Single ended buses</title>
|
|
|
|
<para>A single-ended SCSI bus uses signals that are either 5 Volts
|
|
or 0 Volts (indeed, TTL levels) and are relative to a COMMON
|
|
ground reference. A singled ended 8 bit SCSI bus has
|
|
approximately 25 ground lines, who are all tied to a single <quote>rail</quote>
|
|
on all devices. A standard single ended bus has a maximum length
|
|
of 6 meters. If the same bus is used with fast-SCSI devices, the
|
|
maximum length allowed drops to 3 meters. Fast-SCSI means that
|
|
instead of 5Mbytes/sec the bus allows 10Mbytes/sec
|
|
transfers.</para>
|
|
|
|
<para>Fast-20 (Ultra SCSI) and Fast-40 allow for 20 and 40 million
|
|
transfers/second respectively. So, F20 is 20 Mbytes/second on a 8
|
|
bit bus, 40 Mbytes/second on a 16 bit bus etc. For F20 the max
|
|
bus length is 1.5 meters, for F40 it becomes 0.75 meters. Be
|
|
aware that F20 is pushing the limits quite a bit, so you will
|
|
quickly find out if your SCSI bus is electrically sound.</para>
|
|
|
|
<note>
|
|
<para>If some devices on your bus use <quote>fast</quote> to communicate your
|
|
bus must adhere to the length restrictions for fast
|
|
buses!</para>
|
|
</note>
|
|
|
|
<para>It is obvious that with the newer fast-SCSI devices the bus
|
|
length can become a real bottleneck. This is why the differential
|
|
SCSI bus was introduced in the SCSI-2 standard.</para>
|
|
|
|
<para>For connector pinning and connector types please refer to the
|
|
SCSI-2 standard (see <link linkend="scsi-further-reading">Further
|
|
reading</link>) itself, connectors etc are listed there in
|
|
painstaking detail.</para>
|
|
|
|
<para>Beware of devices using non-standard cabling. For instance
|
|
Apple uses a 25pin D-type connecter (like the one on serial ports
|
|
and parallel printers). Considering that the official SCSI bus
|
|
needs 50 pins you can imagine the use of this connector needs some
|
|
<quote>creative cabling</quote>. The reduction of the number of ground wires
|
|
they used is a bad idea, you better stick to 50 pins cabling in
|
|
accordance with the SCSI standard. For Fast-20 and 40 do not even
|
|
think about buses like this.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Differential buses</title>
|
|
|
|
<para>A differential SCSI bus has a maximum length of 25 meters.
|
|
Quite a difference from the 3 meters for a single-ended fast-SCSI
|
|
bus. The idea behind differential signals is that each bus signal
|
|
has its own return wire. So, each signal is carried on a
|
|
(preferably twisted) pair of wires. The voltage difference
|
|
between these two wires determines whether the signal is asserted
|
|
or de-asserted. To a certain extent the voltage difference
|
|
between ground and the signal wire pair is not relevant (do not
|
|
try 10 kVolts though).</para>
|
|
|
|
<para>It is beyond the scope of this document to explain why this
|
|
differential idea is so much better. Just accept that
|
|
electrically seen the use of differential signals gives a much
|
|
better noise margin. You will normally find differential buses in
|
|
use for inter-cabinet connections. Because of the lower cost
|
|
single ended is mostly used for shorter buses like inside
|
|
cabinets.</para>
|
|
|
|
<para>There is nothing that stops you from using differential stuff
|
|
with FreeBSD, as long as you use a controller that has device
|
|
driver support in FreeBSD. As an example, Adaptec marketed the
|
|
AHA1740 as a single ended board, whereas the AHA1744 was
|
|
differential. The software interface to the host is identical for
|
|
both.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Terminators</title>
|
|
|
|
<para>Terminators in SCSI terminology are resistor networks that are
|
|
used to get a correct impedance matching. Impedance matching is
|
|
important to get clean signals on the bus, without reflections or
|
|
ringing. If you once made a long distance telephone call on a bad
|
|
line you probably know what reflections are. With 20Mbytes/sec
|
|
traveling over your SCSI bus, you do not want signals echoing
|
|
back.</para>
|
|
|
|
<para>Terminators come in various incarnations, with more or less
|
|
sophisticated designs. Of course, there are internal and external
|
|
variants. Many SCSI devices come with a number of sockets in
|
|
which a number of resistor networks can (must be!) installed. If
|
|
you remove terminators from a device, carefully store them. You
|
|
will need them when you ever decide to reconfigure your SCSI bus.
|
|
There is enough variation in even these simple tiny things to make
|
|
finding the exact replacement a frustrating business. There are
|
|
also SCSI devices that have a single jumper to enable or disable a
|
|
built-in terminator. There are special terminators you can stick
|
|
onto a flat cable bus. Others look like external connectors, or a
|
|
connector hood without a cable. So, lots of choice as you can
|
|
see.</para>
|
|
|
|
<para>There is much debate going on if and when you should switch
|
|
from simple resistor (passive) terminators to active terminators.
|
|
Active terminators contain slightly more elaborate circuit to give
|
|
cleaner bus signals. The general consensus seems to be that the
|
|
usefulness of active termination increases when you have long
|
|
buses and/or fast devices. If you ever have problems with your
|
|
SCSI buses you might consider trying an active terminator. Try to
|
|
borrow one first, they reputedly are quite expensive.</para>
|
|
|
|
<para>Please keep in mind that terminators for differential and
|
|
single-ended buses are not identical. You should <emphasis>not
|
|
mix</emphasis> the two variants.</para>
|
|
|
|
<para>OK, and now where should you install your terminators? This is
|
|
by far the most misunderstood part of SCSI. And it is by far the
|
|
simplest. The rule is: <emphasis>every single line on the SCSI
|
|
bus has 2 (two) terminators, one at each end of the
|
|
bus.</emphasis> So, two and not one or three or whatever. Do
|
|
yourself a favor and stick to this rule. It will save you endless
|
|
grief, because wrong termination has the potential to introduce
|
|
highly mysterious bugs. (Note the <quote>potential</quote> here;
|
|
the nastiest part is that it may or may not work.)</para>
|
|
|
|
<para>A common pitfall is to have an internal (flat) cable in a
|
|
machine and also an external cable attached to the controller. It
|
|
seems almost everybody forgets to remove the terminators from the
|
|
controller. The terminator must now be on the last external
|
|
device, and not on the controller! In general, every
|
|
reconfiguration of a SCSI bus must pay attention to this.</para>
|
|
|
|
<note>
|
|
<para>Termination is to be done on a per-line basis. This means
|
|
if you have both narrow and wide buses connected to the same
|
|
host adapter, you need to enable termination on the higher 8
|
|
bits of the bus on the adapter (as well as the last devices on
|
|
each bus, of course).</para>
|
|
</note>
|
|
|
|
<para>What I did myself is remove all terminators from my SCSI
|
|
devices and controllers. I own a couple of external terminators,
|
|
for both the Centronics-type external cabling and for the internal
|
|
flat cable connectors. This makes reconfiguration much
|
|
easier.</para>
|
|
|
|
<para>On modern devices, sometimes integrated terminators are used.
|
|
These things are special purpose integrated circuits that can be
|
|
enabled or disabled with a control pin. It is not necessary to
|
|
physically remove them from a device. You may find them on newer
|
|
host adapters, sometimes they are software configurable, using
|
|
some sort of setup tool. Some will even auto-detect the cables
|
|
attached to the connectors and automatically set up the
|
|
termination as necessary. At any rate, consult your
|
|
documentation!</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Terminator power</title>
|
|
|
|
<para>The terminators discussed in the previous chapter need power
|
|
to operate properly. On the SCSI bus, a line is dedicated to this
|
|
purpose. So, simple huh?</para>
|
|
|
|
<para>Not so. Each device can provide its own terminator power to
|
|
the terminator sockets it has on-device. But if you have external
|
|
terminators, or when the device supplying the terminator power to
|
|
the SCSI bus line is switched off you are in trouble.</para>
|
|
|
|
<para>The idea is that initiators (these are devices that initiate
|
|
actions on the bus, a discussion follows) must supply terminator
|
|
power. All SCSI devices are allowed (but not required) to supply
|
|
terminator power.</para>
|
|
|
|
<para>To allow for un-powered devices on a bus, the terminator power
|
|
must be supplied to the bus via a diode. This prevents the
|
|
backflow of current to un-powered devices.</para>
|
|
|
|
<para>To prevent all kinds of nastiness, the terminator power is
|
|
usually fused. As you can imagine, fuses might blow. This can,
|
|
but does not have to, lead to a non functional bus. If multiple
|
|
devices supply terminator power, a single blown fuse will not put
|
|
you out of business. A single supplier with a blown fuse
|
|
certainly will. Clever external terminators sometimes have a LED
|
|
indication that shows whether terminator power is present.</para>
|
|
|
|
<para>In newer designs auto-restoring fuses that <quote>reset</quote> themselves
|
|
after some time are sometimes used.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Device addressing</title>
|
|
|
|
<para>Because the SCSI bus is, ehh, a bus there must be a way to
|
|
distinguish or address the different devices connected to
|
|
it.</para>
|
|
|
|
<para>This is done by means of the SCSI or target ID. Each device
|
|
has a unique target ID. You can select the ID to which a device
|
|
must respond using a set of jumpers, or a dip switch, or something
|
|
similar. Some SCSI host adapters let you change the target ID
|
|
from the boot menu. (Yet some others will not let you change the
|
|
ID from 7.) Consult the documentation of your device for more
|
|
information.</para>
|
|
|
|
<para>Beware of multiple devices configured to use the same ID.
|
|
Chaos normally reigns in this case. A pitfall is that one of the
|
|
devices sharing the same ID sometimes even manages to answer to
|
|
I/O requests!</para>
|
|
|
|
<para>For an 8 bit bus, a maximum of 8 targets is possible. The
|
|
maximum is 8 because the selection is done bitwise using the 8
|
|
data lines on the bus. For wide buses this increases to the
|
|
number of data lines (usually 16).</para>
|
|
|
|
<note>
|
|
<para>A narrow SCSI device can not communicate with a SCSI device
|
|
with a target ID larger than 7. This means it is generally not
|
|
a good idea to move your SCSI host adapter's target ID to
|
|
something higher than 7 (or your CDROM will stop
|
|
working).</para>
|
|
</note>
|
|
|
|
<para>The higher the SCSI target ID, the higher the priority the
|
|
devices has. When it comes to arbitration between devices that
|
|
want to use the bus at the same time, the device that has the
|
|
highest SCSI ID will win. This also means that the SCSI host
|
|
adapter usually uses target ID 7. Note however that the lower 8
|
|
IDs have higher priorities than the higher 8 IDs on a wide-SCSI
|
|
bus. Thus, the order of target IDs is: [7 6 .. 1 0 15 14 .. 9 8]
|
|
on a wide-SCSI system. (If you are wondering why the lower 8
|
|
have higher priority, read the previous paragraph for a
|
|
hint.)</para>
|
|
|
|
<para>For a further subdivision, the standard allows for Logical
|
|
Units or LUNs for short. A single target ID may have multiple
|
|
LUNs. For example, a tape device including a tape changer may
|
|
have LUN 0 for the tape device itself, and LUN 1 for the tape
|
|
changer. In this way, the host system can address each of the
|
|
functional units of the tape changer as desired.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Bus layout</title>
|
|
|
|
<para>SCSI buses are linear. So, not shaped like Y-junctions, star
|
|
topologies, rings, cobwebs or whatever else people might want to
|
|
invent. One of the most common mistakes is for people with
|
|
wide-SCSI host adapters to connect devices on all three connecters
|
|
(external connector, internal wide connector, internal narrow
|
|
connector). Do not do that. It may appear to work if you are
|
|
really lucky, but I can almost guarantee that your system will
|
|
stop functioning at the most unfortunate moment (this is also
|
|
known as <quote>Murphy's law</quote>).</para>
|
|
|
|
<para>You might notice that the terminator issue discussed earlier
|
|
becomes rather hairy if your bus is not linear. Also, if you have
|
|
more connectors than devices on your internal SCSI cable, make
|
|
sure you attach devices on connectors on both ends instead of
|
|
using the connectors in the middle and let one or both ends
|
|
dangle. This will screw up the termination of the bus.</para>
|
|
|
|
<para>The electrical characteristics, its noise margins and
|
|
ultimately the reliability of it all are tightly related to linear
|
|
bus rule.</para>
|
|
|
|
<para><emphasis>Stick to the linear bus rule!</emphasis></para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Using SCSI with FreeBSD</title>
|
|
|
|
<sect3>
|
|
<title>About translations, BIOSes and magic...</title>
|
|
|
|
<para>As stated before, you should first make sure that you have a
|
|
electrically sound bus.</para>
|
|
|
|
<para>When you want to use a SCSI disk on your PC as boot disk, you
|
|
must aware of some quirks related to PC BIOSes. The PC BIOS in
|
|
its first incarnation used a low level physical interface to the
|
|
hard disk. So, you had to tell the BIOS (using a setup tool or a
|
|
BIOS built-in setup) how your disk physically looked like. This
|
|
involved stating number of heads, number of cylinders, number of
|
|
sectors per track, obscure things like precompensation and reduced
|
|
write current cylinder etc.</para>
|
|
|
|
<para>One might be inclined to think that since SCSI disks are smart
|
|
you can forget about this. Alas, the arcane setup issue is still
|
|
present today. The system BIOS needs to know how to access your
|
|
SCSI disk with the head/cyl/sector method in order to load the
|
|
FreeBSD kernel during boot.</para>
|
|
|
|
<para>The SCSI host adapter or SCSI controller you have put in your
|
|
AT/EISA/PCI/whatever bus to connect your disk therefore has its
|
|
own on-board BIOS. During system startup, the SCSI BIOS takes
|
|
over the hard disk interface routines from the system BIOS. To
|
|
fool the system BIOS, the system setup is normally set to No hard
|
|
disk present. Obvious, is it not?</para>
|
|
|
|
<para>The SCSI BIOS itself presents to the system a so called
|
|
<emphasis>translated</emphasis> drive. This means that a fake
|
|
drive table is constructed that allows the PC to boot the drive.
|
|
This translation is often (but not always) done using a pseudo
|
|
drive with 64 heads and 32 sectors per track. By varying the
|
|
number of cylinders, the SCSI BIOS adapts to the actual drive
|
|
size. It is useful to note that 32 * 64 / 2 = the size of your
|
|
drive in megabytes. The division by 2 is to get from disk blocks
|
|
that are normally 512 bytes in size to Kbytes.</para>
|
|
|
|
<para>Right. All is well now?! No, it is not. The system BIOS has
|
|
another quirk you might run into. The number of cylinders of a
|
|
bootable hard disk cannot be greater than 1024. Using the
|
|
translation above, this is a show-stopper for disks greater than 1
|
|
GB. With disk capacities going up all the time this is causing
|
|
problems.</para>
|
|
|
|
<para>Fortunately, the solution is simple: just use another
|
|
translation, e.g. with 128 heads instead of 32. In most cases new
|
|
SCSI BIOS versions are available to upgrade older SCSI host
|
|
adapters. Some newer adapters have an option, in the form of a
|
|
jumper or software setup selection, to switch the translation the
|
|
SCSI BIOS uses.</para>
|
|
|
|
<para>It is very important that <emphasis>all</emphasis> operating
|
|
systems on the disk use the <emphasis>same translation</emphasis>
|
|
to get the right idea about where to find the relevant partitions.
|
|
So, when installing FreeBSD you must answer any questions about
|
|
heads/cylinders etc using the translated values your host adapter
|
|
uses.</para>
|
|
|
|
<para>Failing to observe the translation issue might lead to
|
|
un-bootable systems or operating systems overwriting each others
|
|
partitions. Using fdisk you should be able to see all
|
|
partitions.</para>
|
|
|
|
<para>You might have heard some talk of <quote>lying</quote> devices?
|
|
Older FreeBSD kernels used to report the geometry of SCSI disks
|
|
when booting. An example from one of my systems:</para>
|
|
|
|
<screen>aha0 targ 0 lun 0: <MICROP 1588-15MB1057404HSP4>
|
|
da0: 636MB (1303250 total sec), 1632 cyl, 15 head, 53 sec, bytes/sec 512</screen>
|
|
|
|
<para>Newer kernels usually do not report this information.
|
|
e.g.</para>
|
|
|
|
<screen>(bt0:0:0): "SEAGATE ST41651 7574" type 0 fixed SCSI 2
|
|
da0(bt0:0:0): Direct-Access 1350MB (2766300 512 byte sectors)</screen>
|
|
|
|
<para>Why has this changed?</para>
|
|
|
|
<para>This info is retrieved from the SCSI disk itself. Newer disks
|
|
often use a technique called zone bit recording. The idea is that
|
|
on the outer cylinders of the drive there is more space so more
|
|
sectors per track can be put on them. This results in disks that
|
|
have more tracks on outer cylinders than on the inner cylinders
|
|
and, last but not least, have more capacity. You can imagine that
|
|
the value reported by the drive when inquiring about the geometry
|
|
now becomes suspect at best, and nearly always misleading. When
|
|
asked for a geometry, it is nearly always better to supply the
|
|
geometry used by the BIOS, or <emphasis>if the BIOS is never going
|
|
to know about this disk</emphasis>, (e.g. it is not a booting
|
|
disk) to supply a fictitious geometry that is convenient.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>SCSI subsystem design</title>
|
|
|
|
<para>FreeBSD uses a layered SCSI subsystem. For each different
|
|
controller card a device driver is written. This driver knows all
|
|
the intimate details about the hardware it controls. The driver
|
|
has a interface to the upper layers of the SCSI subsystem through
|
|
which it receives its commands and reports back any status.</para>
|
|
|
|
<para>On top of the card drivers there are a number of more generic
|
|
drivers for a class of devices. More specific: a driver for tape
|
|
devices (abbreviation: sa, for serial access),
|
|
magnetic disks (da, for direct access), CDROMs (cd) etc.
|
|
In case you are wondering where you can find this stuff, it all
|
|
lives in <filename>/sys/cam/scsi</filename>. See the man pages in
|
|
section 4 for more details.</para>
|
|
|
|
<para>The multi level design allows a decoupling of low-level bit
|
|
banging and more high level stuff. Adding support for another
|
|
piece of hardware is a much more manageable problem.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Kernel configuration</title>
|
|
|
|
<para>Dependent on your hardware, the kernel configuration file must
|
|
contain one or more lines describing your host adapter(s). This
|
|
includes I/O addresses, interrupts etc. Consult the manual page for
|
|
your adapter driver to get more info. Apart from that, check out
|
|
<filename>/sys/i386/conf/LINT</filename> for an overview of a
|
|
kernel config file. <filename>LINT</filename> contains every
|
|
possible option you can dream of. It does
|
|
<emphasis>not</emphasis> imply <filename>LINT</filename> will
|
|
actually get you to a working kernel at all.</para>
|
|
|
|
<para>Although it is probably stating the obvious: the kernel config
|
|
file should reflect your actual hardware setup. So, interrupts,
|
|
I/O addresses etc must match the kernel config file. During
|
|
system boot messages will be displayed to indicate whether the
|
|
configured hardware was actually found.</para>
|
|
|
|
<note>
|
|
<para>Note that most of the EISA/PCI drivers (namely
|
|
<devicename>ahb</devicename>, <devicename>ahc</devicename>,
|
|
<devicename>ncr</devicename> and <devicename>amd</devicename>
|
|
will automatically obtain the correct parameters from the host
|
|
adapters themselves at boot time; thus, you just need to write,
|
|
for instance, <literal>controller ahc0</literal>.</para>
|
|
</note>
|
|
|
|
<para>An example loosely based on the FreeBSD 2.2.5-Release kernel
|
|
config file <filename>LINT</filename> with some added comments
|
|
(between []):</para>
|
|
|
|
<programlisting># SCSI host adapters: `aha', `ahb', `aic', `bt', `nca'
|
|
#
|
|
# aha: Adaptec 154x
|
|
# ahb: Adaptec 174x
|
|
# ahc: Adaptec 274x/284x/294x
|
|
# aic: Adaptec 152x and sound cards using the Adaptec AIC-6360 (slow!)
|
|
# amd: AMD 53c974 based SCSI cards (e.g., Tekram DC-390 and 390T)
|
|
# bt: Most Buslogic controllers
|
|
# nca: ProAudioSpectrum cards using the NCR 5380 or Trantor T130
|
|
# ncr: NCR/Symbios 53c810/815/825/875 etc based SCSI cards
|
|
# uha: UltraStore 14F and 34F
|
|
# sea: Seagate ST01/02 8 bit controller (slow!)
|
|
# wds: Western Digital WD7000 controller (no scatter/gather!).
|
|
#
|
|
|
|
[For an Adaptec AHA274x/284x/294x/394x etc controller]
|
|
controller ahc0
|
|
|
|
[For an NCR/Symbios 53c875 based controller]
|
|
controller ncr0
|
|
|
|
[For an Ultrastor adapter]
|
|
controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr
|
|
|
|
# Map SCSI buses to specific SCSI adapters
|
|
controller scbus0 at ahc0
|
|
controller scbus2 at ncr0
|
|
controller scbus1 at uha0
|
|
|
|
# The actual SCSI devices
|
|
disk da0 at scbus0 target 0 unit 0 [SCSI disk 0 is at scbus 0, LUN 0]
|
|
disk da1 at scbus0 target 1 [implicit LUN 0 if omitted]
|
|
disk da2 at scbus1 target 3 [SCSI disk on the uha0]
|
|
disk da3 at scbus2 target 4 [SCSI disk on the ncr0]
|
|
tape sa1 at scbus0 target 6 [SCSI tape at target 6]
|
|
device cd0 at scbus? [the first ever CDROM found, no wiring]</programlisting>
|
|
|
|
<para>The example above tells the kernel to look for a ahc (Adaptec
|
|
274x) controller, then for an NCR/Symbios board, and so on. The
|
|
lines following the controller specifications tell the kernel to
|
|
configure specific devices but <emphasis>only</emphasis> attach
|
|
them when they match the target ID and LUN specified on the
|
|
corresponding bus.</para>
|
|
|
|
<para>Wired down devices get <quote>first shot</quote> at the unit
|
|
numbers so the first non <quote>wired down</quote> device, is
|
|
allocated the unit number one greater than the highest
|
|
<quote>wired down</quote> unit number for that kind of device. So,
|
|
if you had a SCSI tape at target ID 2 it would be configured as
|
|
sa2, as the tape at target ID 6 is wired down to unit number
|
|
1.</para>
|
|
|
|
<note>
|
|
<para>Wired down devices need not be found to get their unit
|
|
number. The unit number for a wired down device is reserved for
|
|
that device, even if it is turned off at boot time. This allows
|
|
the device to be turned on and brought on-line at a later time,
|
|
without rebooting. Notice that a device's unit number has
|
|
<emphasis>no</emphasis> relationship with its target ID on the
|
|
SCSI bus.</para>
|
|
</note>
|
|
|
|
<para>Below is another example of a kernel config file as used by
|
|
FreeBSD version < 2.0.5. The difference with the first example
|
|
is that devices are not <quote>wired down</quote>. <quote>Wired
|
|
down</quote> means that you specify which SCSI target belongs to
|
|
which device.</para>
|
|
|
|
<para>A kernel built to the config file below will attach the first
|
|
SCSI disk it finds to da0, the second disk to da1 etc. If you ever
|
|
removed or added a disk, all other devices of the same type (disk
|
|
in this case) would <quote>move around</quote>. This implies you have to
|
|
change <filename>/etc/fstab</filename> each time.</para>
|
|
|
|
<para>Although the old style still works, you are
|
|
<emphasis>strongly</emphasis> recommended to use this new feature.
|
|
It will save you a lot of grief whenever you shift your hardware
|
|
around on the SCSI buses. So, when you re-use your old trusty
|
|
config file after upgrading from a pre-FreeBSD2.0.5.R system check
|
|
this out.</para>
|
|
|
|
<programlisting>[driver for Adaptec 174x]
|
|
controller ahb0 at isa? bio irq 11 vector ahbintr
|
|
|
|
[for Adaptec 154x]
|
|
controller aha0 at isa? port "IO_AHA0" bio irq 11 drq 5 vector ahaintr
|
|
|
|
[for Seagate ST01/02]
|
|
controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr
|
|
|
|
controller scbus0
|
|
|
|
device da0 [support for 4 SCSI harddisks, da0 up da3]
|
|
device sa0 [support for 2 SCSI tapes]
|
|
|
|
[for the CDROM]
|
|
device cd0 #Only need one of these, the code dynamically grows</programlisting>
|
|
|
|
<para>Both examples support SCSI disks. If during boot more devices
|
|
of a specific type (e.g. da disks) are found than are configured
|
|
in the booting kernel, the system will simply allocate more
|
|
devices, incrementing the unit number starting at the last number
|
|
<quote>wired down</quote>. If there are no <quote>wired
|
|
down</quote> devices then counting starts at unit 0.</para>
|
|
|
|
<para>Use <command>man 4 scsi</command> to check for the latest info
|
|
on the SCSI subsystem. For more detailed info on host adapter
|
|
drivers use e.g., <command>man 4 ahc</command> for info on the
|
|
Adaptec 294x driver.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Tuning your SCSI kernel setup</title>
|
|
|
|
<para>Experience has shown that some devices are slow to respond to
|
|
INQUIRY commands after a SCSI bus reset (which happens at boot
|
|
time). An INQUIRY command is sent by the kernel on boot to see
|
|
what kind of device (disk, tape, CDROM etc.) is connected to a
|
|
specific target ID. This process is called device probing by the
|
|
way.</para>
|
|
|
|
<para>To work around the <quote>slow response</quote> problem, FreeBSD allows a
|
|
tunable delay time before the SCSI devices are probed following a
|
|
SCSI bus reset. You can set this delay time in your kernel
|
|
configuration file using a line like:</para>
|
|
|
|
<programlisting>options SCSI_DELAY=15 #Be pessimistic about Joe SCSI device</programlisting>
|
|
|
|
<para>This line sets the delay time to 15 seconds. On my own system
|
|
I had to use 3 seconds minimum to get my trusty old CDROM drive
|
|
to be recognized. Start with a high value (say 30 seconds or so)
|
|
when you have problems with device recognition. If this helps,
|
|
tune it back until it just stays working.</para>
|
|
</sect3>
|
|
|
|
<sect3 id="scsi-rogue-devices">
|
|
<title>Rogue SCSI devices</title>
|
|
|
|
<para>Although the SCSI standard tries to be complete and concise,
|
|
it is a complex standard and implementing things correctly is no
|
|
easy task. Some vendors do a better job then others.</para>
|
|
|
|
<para>This is exactly where the <quote>rogue</quote> devices come
|
|
into view. Rogues are devices that are recognized by the FreeBSD
|
|
kernel as behaving slightly (...) non-standard. Rogue devices are
|
|
reported by the kernel when booting. An example for two of my
|
|
cartridge tape units:</para>
|
|
|
|
<screen>Feb 25 21:03:34 yedi /kernel: ahb0 targ 5 lun 0: <TANDBERG TDC 3600 -06:>
|
|
Feb 25 21:03:34 yedi /kernel: sa0: Tandberg tdc3600 is a known rogue
|
|
|
|
Mar 29 21:16:37 yedi /kernel: aha0 targ 5 lun 0: <ARCHIVE VIPER 150 21247-005>
|
|
Mar 29 21:16:37 yedi /kernel: sa1: Archive Viper 150 is a known rogue </screen>
|
|
|
|
<para>For instance, there are devices that respond to all LUNs on a
|
|
certain target ID, even if they are actually only one device. It
|
|
is easy to see that the kernel might be fooled into believing that
|
|
there are 8 LUNs at that particular target ID. The confusion this
|
|
causes is left as an exercise to the reader.</para>
|
|
|
|
<para>The SCSI subsystem of FreeBSD recognizes devices with bad
|
|
habits by looking at the INQUIRY response they send when probed.
|
|
Because the INQUIRY response also includes the version number of
|
|
the device firmware, it is even possible that for different
|
|
firmware versions different workarounds are used. See e.g.
|
|
<filename>/sys/cam/scsi/scsi_sa.c</filename> and
|
|
<filename>/sys/cam/scsi/scsi_all.c</filename> for more info on how
|
|
this is done.</para>
|
|
|
|
<para>This scheme works fine, but keep in mind that it of course
|
|
only works for devices that are known to be weird. If you are the
|
|
first to connect your bogus Mumbletech SCSI CDROM you might be
|
|
the one that has to define which workaround is needed.</para>
|
|
|
|
<para>After you got your Mumbletech working, please send the
|
|
required workaround to the FreeBSD development team for inclusion
|
|
in the next release of FreeBSD. Other Mumbletech owners will be
|
|
grateful to you.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Multiple LUN devices</title>
|
|
|
|
<para>In some cases you come across devices that use multiple
|
|
logical units (LUNs) on a single SCSI ID. In most cases FreeBSD
|
|
only probes devices for LUN 0. An example are so called bridge
|
|
boards that connect 2 non-SCSI hard disks to a SCSI bus (e.g. an
|
|
Emulex MD21 found in old Sun systems).</para>
|
|
|
|
<para>This means that any devices with LUNs != 0 are not normally
|
|
found during device probe on system boot. To work around this
|
|
problem you must add an appropriate entry in /sys/cam/scsi
|
|
and rebuild your kernel.</para>
|
|
|
|
<para>Look for a struct that is initialized like below:
|
|
(FIXME: which file? Do these entries still exist in this form
|
|
now that we use CAM?)</para>
|
|
|
|
<programlisting>{
|
|
T_DIRECT, T_FIXED, "MAXTOR", "XT-4170S", "B5A",
|
|
"mx1", SC_ONE_LU
|
|
}</programlisting>
|
|
|
|
<para>For your Mumbletech BRIDGE2000 that has more than one LUN, acts
|
|
as a SCSI disk and has firmware revision 123 you would add
|
|
something like:</para>
|
|
|
|
<programlisting>{
|
|
T_DIRECT, T_FIXED, "MUMBLETECH", "BRIDGE2000", "123",
|
|
"da", SC_MORE_LUS
|
|
}</programlisting>
|
|
|
|
<para>The kernel on boot scans the inquiry data it receives against
|
|
the table and acts accordingly. See the source for more
|
|
info.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Tagged command queuing</title>
|
|
|
|
<para>Modern SCSI devices, particularly magnetic disks,
|
|
support what is called tagged command queuing (TCQ).</para>
|
|
|
|
<para>In a nutshell, TCQ allows the device to have multiple I/O
|
|
requests outstanding at the same time. Because the device is
|
|
intelligent, it can optimize its operations (like head
|
|
positioning) based on its own request queue. On SCSI devices
|
|
like RAID (Redundant Array of Independent Disks) arrays the TCQ
|
|
function is indispensable to take advantage of the device's
|
|
inherent parallelism.</para>
|
|
|
|
<para>Each I/O request is uniquely identified by a <quote>tag</quote>
|
|
(hence the name tagged command queuing) and this tag is used by
|
|
FreeBSD to see which I/O in the device drivers queue is reported
|
|
as complete by the device.</para>
|
|
|
|
<para>It should be noted however that TCQ requires device driver
|
|
support and that some devices implemented it <quote>not quite
|
|
right</quote> in their firmware. This problem bit me once, and it
|
|
leads to highly mysterious problems. In such cases, try to
|
|
disable TCQ.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Bus-master host adapters</title>
|
|
|
|
<para>Most, but not all, SCSI host adapters are bus mastering
|
|
controllers. This means that they can do I/O on their own without
|
|
putting load onto the host CPU for data movement.</para>
|
|
|
|
<para>This is of course an advantage for a multitasking operating
|
|
system like FreeBSD. It must be noted however that there might be
|
|
some rough edges.</para>
|
|
|
|
<para>For instance an Adaptec 1542 controller can be set to use
|
|
different transfer speeds on the host bus (ISA or AT in this
|
|
case). The controller is settable to different rates because not
|
|
all motherboards can handle the higher speeds. Problems like
|
|
hang-ups, bad data etc might be the result of using a higher data
|
|
transfer rate then your motherboard can stomach.</para>
|
|
|
|
<para>The solution is of course obvious: switch to a lower data
|
|
transfer rate and try if that works better.</para>
|
|
|
|
<para>In the case of a Adaptec 1542, there is an option that can be
|
|
put into the kernel config file to allow dynamic determination of
|
|
the right, read: fastest feasible, transfer rate. This option is
|
|
disabled by default:</para>
|
|
|
|
<programlisting>options "TUNE_1542" #dynamic tune of bus DMA speed</programlisting>
|
|
|
|
<para>Check the manual pages for the host adapter that you use. Or
|
|
better still, use the ultimate documentation (read: driver
|
|
source).</para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Tracking down problems</title>
|
|
|
|
<para>The following list is an attempt to give a guideline for the
|
|
most common SCSI problems and their solutions. It is by no means
|
|
complete.</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para>Check for loose connectors and cables.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Check and double check the location and number of your
|
|
terminators.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Check if your bus has at least one supplier of terminator
|
|
power (especially with external terminators.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Check if no double target IDs are used.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Check if all devices to be used are powered up.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Make a minimal bus config with as little devices as
|
|
possible.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If possible, configure your host adapter to use slow bus
|
|
speeds.</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Disable tagged command queuing to make things as simple as
|
|
possible (for a NCR host adapter based system see man
|
|
ncrcontrol)</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>If you can compile a kernel, make one with the
|
|
<literal>SCSIDEBUG</literal> option, and try accessing the
|
|
device with debugging turned on for that device. If your device
|
|
does not even probe at startup, you may have to define the
|
|
address of the device that is failing, and the desired debug
|
|
level in <filename>/sys/cam/cam_debug.h</filename>. If it
|
|
probes but just does not work, you can use the
|
|
&man.camcontrol.8; command to dynamically set a debug level to
|
|
it in a running kernel (if <literal>CAMDEBUG</literal> is
|
|
defined). This will give you <emphasis>copious</emphasis>
|
|
debugging output with which to confuse the gurus. See
|
|
<command>man camcontrol</command> for more exact information. Also
|
|
look at <command>man 4 pass</command>.</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
</sect2>
|
|
|
|
<sect2 id="scsi-further-reading">
|
|
<title>Further reading</title>
|
|
|
|
<para>If you intend to do some serious SCSI hacking, you might want to
|
|
have the official standard at hand:</para>
|
|
|
|
<para>Approved American National Standards can be purchased from
|
|
ANSI at
|
|
|
|
<address>
|
|
<otheraddr>13th Floor</otheraddr>
|
|
<street>11 West 42nd Street</street>
|
|
<city>New York</city>
|
|
<state>NY</state> <postcode>10036</postcode>
|
|
Sales Dept: <phone>(212) 642-4900</phone>
|
|
</address>
|
|
</para>
|
|
|
|
<para>You can also buy many ANSI
|
|
standards and most committee draft documents from Global
|
|
Engineering Documents,
|
|
|
|
<address>
|
|
<street>15 Inverness Way East</street>
|
|
<city>Englewood</city>
|
|
<state>CO</state>, <postcode>80112-5704</postcode>
|
|
Phone: <phone>(800) 854-7179</phone>
|
|
Outside USA and Canada: <phone>(303) 792-2181</phone>
|
|
Fax: <fax>(303) 792- 2192</fax>
|
|
</address>
|
|
</para>
|
|
|
|
<para>Many X3T10 draft documents are available electronically on the
|
|
SCSI BBS (719-574-0424) and on the <hostid
|
|
role="fqdn">ncrinfo.ncr.com</hostid> anonymous FTP site.</para>
|
|
|
|
<para>Latest X3T10 committee documents are:</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para>AT Attachment (ATA or IDE) [X3.221-1994]
|
|
(<emphasis>Approved</emphasis>)</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>ATA Extensions (ATA-2) [X3T10/948D Rev 2i]</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Enhanced Small Device Interface (ESDI)
|
|
[X3.170-1990/X3.170a-1991]
|
|
(<emphasis>Approved</emphasis>)</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>Small Computer System Interface — 2 (SCSI-2)
|
|
[X3.131-1994] (<emphasis>Approved</emphasis>)</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para>SCSI-2 Common Access Method Transport and SCSI Interface
|
|
Module (CAM) [X3T10/792D Rev 11]</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
|
|
<para>Other publications that might provide you with additional
|
|
information are:</para>
|
|
|
|
<itemizedlist>
|
|
<listitem>
|
|
<para><quote>SCSI: Understanding the Small Computer System
|
|
Interface</quote>, written by NCR Corporation. Available from:
|
|
Prentice Hall, Englewood Cliffs, NJ, 07632 Phone: (201) 767-5937
|
|
ISBN 0-13-796855-8</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><quote>Basics of SCSI</quote>, a SCSI tutorial written by
|
|
Ancot Corporation Contact Ancot for availability information at:
|
|
Phone: (415) 322-5322 Fax: (415) 322-0455</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><quote>SCSI Interconnection Guide Book</quote>, an AMP
|
|
publication (dated 4/93, Catalog 65237) that lists the various
|
|
SCSI connectors and suggests cabling schemes. Available from
|
|
AMP at (800) 522-6752 or (717) 564-0100</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><quote>Fast Track to SCSI</quote>, A Product Guide written by
|
|
Fujitsu. Available from: Prentice Hall, Englewood Cliffs, NJ,
|
|
07632 Phone: (201) 767-5937 ISBN 0-13-307000-X</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><quote>The SCSI Bench Reference</quote>, <quote>The SCSI
|
|
Encyclopedia</quote>, and the <quote>SCSI Tutor</quote>, ENDL
|
|
Publications, 14426 Black Walnut Court, Saratoga CA, 95070
|
|
Phone: (408) 867-6642</para>
|
|
</listitem>
|
|
|
|
<listitem>
|
|
<para><quote>Zadian SCSI Navigator</quote> (quick ref. book) and
|
|
<quote>Discover the Power of SCSI</quote> (First book along with
|
|
a one-hour video and tutorial book), Zadian Software, Suite 214,
|
|
1210 S. Bascom Ave., San Jose, CA 92128, (408) 293-0800</para>
|
|
</listitem>
|
|
</itemizedlist>
|
|
|
|
<para>On Usenet the newsgroups <ulink
|
|
url="news:comp.periphs.scsi">comp.periphs.scsi</ulink> and <ulink
|
|
url="news:comp.periphs">comp.periphs</ulink> are noteworthy places
|
|
to look for more info. You can also find the <ulink
|
|
url="http://scsifaq.org:9080/scsi_faq/scsifaq.html">SCSI-FAQ</ulink>
|
|
there, which is posted periodically.</para>
|
|
|
|
<para>Most major SCSI device and host adapter suppliers operate FTP
|
|
sites and/or BBS systems. They may be valuable sources of
|
|
information about the devices you own.</para>
|
|
</sect2>
|
|
</sect1>
|
|
|
|
<sect1 id="hw-storage-controllers">
|
|
<title>* Disk/tape controllers</title>
|
|
|
|
<sect2>
|
|
<title>* SCSI</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* IDE</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* Floppy</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
</sect1>
|
|
|
|
<sect1>
|
|
<title>Hard drives</title>
|
|
|
|
<sect2>
|
|
<title>SCSI hard drives</title>
|
|
|
|
<para><emphasis>Contributed by &a.asami;. 17 February
|
|
1998.</emphasis></para>
|
|
|
|
<para>As mentioned in the <link linkend="scsi">SCSI</link> section,
|
|
virtually all SCSI hard drives sold today are SCSI-2 compliant and
|
|
thus will work fine as long as you connect them to a supported SCSI
|
|
host adapter. Most problems people encounter are either due to
|
|
badly designed cabling (cable too long, star topology, etc.),
|
|
insufficient termination, or defective parts. Please refer to the
|
|
<link linkend="scsi">SCSI</link> section first if your SCSI hard
|
|
drive is not working. However, there are a couple of things you may
|
|
want to take into account before you purchase SCSI hard drives for
|
|
your system.</para>
|
|
|
|
<sect3>
|
|
<title>Rotational speed</title>
|
|
|
|
<para>Rotational speeds of SCSI drives sold today range from around
|
|
4,500RPM to 15,000RPM. Most of them are either 7,200RPM or
|
|
10,000RPM, with 15,000RPM becoming affordable (June 2002).
|
|
Even though the 10,000RPM drives can generally transfer
|
|
data faster, they run considerably hotter than their 7,200RPM
|
|
counterparts. A large fraction of today's disk drive malfunctions
|
|
are heat-related. If you do not have very good cooling in your PC
|
|
case, you may want to stick with 7,200RPM or slower drives.</para>
|
|
|
|
<para>Note that newer drives, with higher areal recording densities,
|
|
can deliver much more bits per rotation than older ones. Today's
|
|
top-of-line 7,200RPM drives can sustain a throughput comparable to
|
|
10,000RPM drives of one or two model generations ago. The number
|
|
to find on the spec sheet for bandwidth is <quote>internal data
|
|
(or transfer) rate</quote>. It is usually in megabits/sec so
|
|
divide it by 8 and you will get the rough approximation of how much
|
|
megabytes/sec you can get out of the drive.</para>
|
|
|
|
<para>(If you are a speed maniac and want a 15,000RPM drive for your
|
|
cute little PC, be my guest; however, those drives become
|
|
extremely hot. Do not even think about it if you do not have a fan
|
|
blowing air <emphasis>directly at</emphasis> the drive or a
|
|
properly ventilated disk enclosure.)</para>
|
|
|
|
<para>Obviously, the latest 15,000RPM drives and 10,000RPM drives can
|
|
deliver more data than the latest 7,200RPM drives, so if absolute
|
|
bandwidth is the necessity for your applications, you have little
|
|
choice but to get the faster drives. Also, if you need low
|
|
latency, faster drives are better; not only do they usually have
|
|
lower average seek times, but also the rotational delay is one
|
|
place where slow-spinning drives can never beat a faster one.
|
|
(The average rotational latency is half the time it takes to
|
|
rotate the drive once; thus, it is 2 milliseconds for 15,000RPM,
|
|
3ms for 10,000RPM
|
|
drives, 4.2ms for 7,200RPM drives and 5.6ms for 5,400RPM drives.)
|
|
Latency is seek time plus rotational delay. Make sure you
|
|
understand whether you need low latency or more accesses per
|
|
second, though; in the latter case (e.g., news servers), it may
|
|
not be optimal to purchase one big fast drive. You can achieve
|
|
similar or even better results by using the ccd (concatenated
|
|
disk) driver to create a striped disk array out of multiple slower
|
|
drives for comparable overall cost.</para>
|
|
|
|
<para>Make sure you have adequate air flow around the drive,
|
|
especially if you are going to use a fast-spinning drive. You
|
|
generally need at least 1/2” (1.25cm) of spacing above and below a
|
|
drive. Understand how the air flows through your PC case. Most
|
|
cases have the power supply suck the air out of the back. See
|
|
where the air flows in, and put the drive where it will have the
|
|
largest volume of cool air flowing around it. You may need to seal
|
|
some unwanted holes or add a new fan for effective cooling.</para>
|
|
|
|
<para>Another consideration is noise. Many 10,000 or faster drives
|
|
generate a high-pitched whine which is quite unpleasant to most
|
|
people. That, plus the extra fans often required for cooling, may
|
|
make 10,000 or faster drives unsuitable for some office and home
|
|
environments.</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Form factor</title>
|
|
|
|
<para>Most SCSI drives sold today are of 3.5” form factor. They
|
|
come in two different heights; 1.6” (<quote>half-height</quote>) or
|
|
1” (<quote>low-profile</quote>). The half-height drive is the same
|
|
height as a CDROM drive. However, do not forget the spacing rule
|
|
mentioned in the previous section. If you have three standard
|
|
3.5” drive bays, you will not be able to put three half-height
|
|
drives in there (without frying them, that is).</para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Interface</title>
|
|
|
|
<para>The majority of SCSI hard drives sold today are Ultra,
|
|
Ultra-wide, or Ultra160 SCSI. As of this writing (June 2002),
|
|
the first Ultra320 host adapters and devices become available.
|
|
The maximum bandwidth of Ultra SCSI is 20MB/sec,
|
|
and Ultra-wide SCSI is 40MB/sec. Ultra160 can transfer 160MB/sec
|
|
and Ultra320 can transfer 320MB/sec. There is no difference in max
|
|
cable length between Ultra and Ultra-wide; however, the more
|
|
devices you have on the same bus, the sooner you will start having
|
|
bus integrity problems. Unless you have a well-designed disk
|
|
enclosure, it is not easy to make more than 5 or 6 Ultra SCSI
|
|
drives work on a single bus.</para>
|
|
|
|
<para>On the other hand, if you need to connect many drives, going
|
|
for Fast-wide SCSI may not be a bad idea. That will have the same
|
|
max bandwidth as Ultra (narrow) SCSI, while electronically it is
|
|
much easier to get it <quote>right</quote>. My advice would be: if
|
|
you want to connect many disks, get wide or Ultra160 SCSI drives;
|
|
they usually
|
|
cost a little more but it may save you down the road. (Besides,
|
|
if you can not afford the cost difference, you should not be building
|
|
a disk array.)</para>
|
|
|
|
<para>There are two variant of wide SCSI drives; 68-pin and 80-pin
|
|
SCA (Single Connector Attach). The SCA drives do not have a
|
|
separate 4-pin power connector, and also read the SCSI ID settings
|
|
through the 80-pin connector. If you are really serious about
|
|
building a large storage system, get SCA drives and a good SCA
|
|
enclosure (dual power supply with at least one extra fan). They
|
|
are more electronically sound than 68-pin counterparts because
|
|
there is no <quote>stub</quote> of the SCSI bus inside the disk
|
|
canister as in arrays built from 68-pin drives. They are easier
|
|
to install too (you just need to screw the drive in the canister,
|
|
instead of trying to squeeze in your fingers in a tight place to
|
|
hook up all the little cables (like the SCSI ID and disk activity
|
|
LED lines).</para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* IDE hard drives</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
</sect1>
|
|
|
|
<sect1>
|
|
<title>Tape drives</title>
|
|
|
|
<para><emphasis>Contributed by &a.jmb;. 2 July
|
|
1996.</emphasis></para>
|
|
|
|
<sect2>
|
|
<title>General tape access commands</title>
|
|
|
|
<para>&man.mt.1; provides generic access to the tape drives. Some of
|
|
the more common commands are <command>rewind</command>,
|
|
<command>erase</command>, and <command>status</command>. See the
|
|
&man.mt.1; manual page for a detailed description.</para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Controller Interfaces</title>
|
|
|
|
<para>There are several different interfaces that support tape drives.
|
|
The interfaces are SCSI, IDE, Floppy and Parallel Port. A wide
|
|
variety of tape drives are available for these interfaces.
|
|
Controllers are discussed in <link
|
|
linkend="hw-storage-controllers">Disk/tape
|
|
controllers</link>.</para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>SCSI drives</title>
|
|
|
|
<para>The &man.st.4; driver provides support for 8mm (Exabyte), 4mm
|
|
(DAT: Digital Audio Tape), QIC (Quarter-Inch Cartridge), DLT
|
|
(Digital Linear Tape), QIC Mini cartridge and 9-track (remember the
|
|
big reels that you see spinning in Hollywood computer rooms) tape
|
|
drives. See the &man.st.4; manual page for a detailed
|
|
description.</para>
|
|
|
|
<para>The drives listed below are currently being used by members of
|
|
the FreeBSD community. They are not the only drives that will work
|
|
with FreeBSD. They just happen to be the ones that we use.</para>
|
|
|
|
<sect3>
|
|
<title>4mm (DAT: Digital Audio Tape)</title>
|
|
|
|
<para><link linkend="hw-storage-python-28454">Archive Python
|
|
28454</link></para>
|
|
|
|
<para><link linkend="hw-storage-python-04687">Archive Python
|
|
04687</link></para>
|
|
|
|
<para><link linkend="hw-storage-hp1533a">HP C1533A</link></para>
|
|
|
|
<para><link linkend="hw-storage-hp1534a">HP C1534A</link></para>
|
|
|
|
<para><link linkend="hw-storage-hp35450a">HP 35450A</link></para>
|
|
|
|
<para><link linkend="hw-storage-hp35470a">HP 35470A</link></para>
|
|
|
|
<para><link linkend="hw-storage-hp35480a">HP 35480A</link></para>
|
|
|
|
<para><link linkend="hw-storage-sdt5000">SDT-5000</link></para>
|
|
|
|
<para><link linkend="hw-storage-wangtek6200">Wangtek
|
|
6200</link></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>8mm (Exabyte)</title>
|
|
|
|
<para><link linkend="hw-storage-exb8200">EXB-8200</link></para>
|
|
|
|
<para><link linkend="hw-storage-exb8500">EXB-8500</link></para>
|
|
|
|
<para><link linkend="hw-storage-exb8505">EXB-8505</link></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>QIC (Quarter-Inch Cartridge)</title>
|
|
|
|
<para><link linkend="hw-storage-anaconda">Archive Anaconda
|
|
2750</link></para>
|
|
|
|
<para><link linkend="hw-storage-viper60">Archive Viper
|
|
60</link></para>
|
|
|
|
<para><link linkend="hw-storage-viper150">Archive Viper
|
|
150</link></para>
|
|
|
|
<para><link linkend="hw-storage-viper2525">Archive Viper
|
|
2525</link></para>
|
|
|
|
<para><link linkend="hw-storage-tandberg3600">Tandberg TDC
|
|
3600</link></para>
|
|
|
|
<para><link linkend="hw-storage-tandberg3620">Tandberg TDC
|
|
3620</link></para>
|
|
|
|
<para><link linkend="hw-storage-tandberg3800">Tandberg TDC
|
|
3800</link></para>
|
|
|
|
<para><link linkend="hw-storage-tandberg4222">Tandberg TDC
|
|
4222</link></para>
|
|
|
|
<para><link linkend="hw-storage-wangtek5525es">Wangtek
|
|
5525ES</link></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>DLT (Digital Linear Tape)</title>
|
|
|
|
<para><link linkend="hw-storage-dectz87">Digital TZ87</link></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Mini-Cartridge</title>
|
|
|
|
<para><link linkend="hw-storage-ctms3200">Conner CTMS
|
|
3200</link></para>
|
|
|
|
<para><link linkend="hw-storage-exb2501">Exabyte 2501</link></para>
|
|
</sect3>
|
|
|
|
<sect3>
|
|
<title>Autoloaders/Changers</title>
|
|
|
|
<para><link linkend="hw-storage-hp1553a">Hewlett-Packard HP C1553A
|
|
Autoloading DDS2</link></para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* IDE drives</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Floppy drives</title>
|
|
|
|
<para><link linkend="hw-storage-conner420r">Conner 420R</link></para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* Parallel port drives</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>Detailed Information</title>
|
|
|
|
<sect3 id="hw-storage-anaconda">
|
|
<title>Archive Anaconda 2750</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
ANCDA 2750 28077 -003 type 1 removable SCSI 2</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 1.35GB when using QIC-1350 tapes. This
|
|
drive will read and write QIC-150 (DC6150), QIC-250 (DC6250), and
|
|
QIC-525 (DC6525) tapes as well.</para>
|
|
|
|
<para>Data transfer rate is 350kB/s using &man.dump.8;.
|
|
Rates of 530kB/s have been reported when using
|
|
Amanda</para>
|
|
|
|
<para>Production of this drive has been discontinued.</para>
|
|
|
|
<para>The SCSI bus connector on this tape drive is reversed from
|
|
that on most other SCSI devices. Make sure that you have enough
|
|
SCSI cable to twist the cable one-half turn before and after the
|
|
Archive Anaconda tape drive, or turn your other SCSI devices
|
|
upside-down.</para>
|
|
|
|
<para>Two kernel code changes are required to use this drive. This
|
|
drive will not work as delivered.</para>
|
|
|
|
<para>If you have a SCSI-2 controller, short jumper 6. Otherwise,
|
|
the drive behaves are a SCSI-1 device. When operating as a SCSI-1
|
|
device, this drive, <quote>locks</quote> the SCSI bus during some
|
|
tape operations, including: fsf, rewind, and rewoffl.</para>
|
|
|
|
<para>If you are using the NCR SCSI controllers, patch the file
|
|
<filename>/usr/src/sys/pci/ncr.c</filename> (as shown below).
|
|
Build and install a new kernel.</para>
|
|
|
|
<programlisting>*** 4831,4835 ****
|
|
};
|
|
|
|
! if (np->latetime>4) {
|
|
/*
|
|
** Although we tried to wake it up,
|
|
--- 4831,4836 ----
|
|
};
|
|
|
|
! if (np->latetime>1200) {
|
|
/*
|
|
** Although we tried to wake it up,</programlisting>
|
|
|
|
<para>Reported by: &a.jmb;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-python-28454">
|
|
<title>Archive Python 28454</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
Python 28454-XXX4ASB</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>density code 0x8c, 512-byte
|
|
blocks</literal></para>
|
|
|
|
<para>This is a DDS-1 tape drive.</para>
|
|
|
|
<para>Native capacity is 2.5GB on 90m tapes.</para>
|
|
|
|
<para>Data transfer rate is XXX.</para>
|
|
|
|
<para>This drive was repackaged by Sun Microsystems as model
|
|
595-3067.</para>
|
|
|
|
<para>Reported by: Bob Bishop <email>rb@gid.co.uk</email></para>
|
|
|
|
<para>Throughput is in the 1.5 MByte/sec range, however this will
|
|
drop if the disks and tape drive are on the same SCSI
|
|
controller.</para>
|
|
|
|
<para>Reported by: Robert E. Seastrom
|
|
<email>rs@seastrom.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-python-04687">
|
|
<title>Archive Python 04687</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
Python 04687-XXX 6580</literal> <literal>Removable Sequential
|
|
Access SCSI-2 device</literal></para>
|
|
|
|
<para>This is a DAT-DDS-2 drive.</para>
|
|
|
|
<para>Native capacity is 4GB when using 120m tapes.</para>
|
|
|
|
<para>This drive supports hardware data compression. Switch 4
|
|
controls MRS (Media Recognition System). MRS tapes have stripes
|
|
on the transparent leader. Switch 4 <emphasis>off</emphasis>
|
|
enables MRS, <emphasis>on</emphasis> disables MRS.</para>
|
|
|
|
<para>Parity is controlled by switch 5. Switch 5
|
|
<emphasis>on</emphasis> to enable parity control. Compression is
|
|
enabled with Switch 6 <emphasis>off</emphasis>. It is possible to
|
|
override compression with the <literal>SCSI MODE SELECT</literal>
|
|
command (see &man.mt.1;).</para>
|
|
|
|
<para>Data transfer rate is 800kB/s.</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-viper60">
|
|
<title>Archive Viper 60</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
VIPER 60 21116 -007</literal> <literal>type 1 removable SCSI
|
|
1</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 60MB.</para>
|
|
|
|
<para>Data transfer rate is XXX.</para>
|
|
|
|
<para>Production of this drive has been discontinued.</para>
|
|
|
|
<para>Reported by: Philippe Regnauld
|
|
<email>regnauld@hsc.fr</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-viper150">
|
|
<title>Archive Viper 150</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
VIPER 150 21531 -004</literal> <literal>Archive Viper 150 is a
|
|
known rogue</literal> <literal>type 1 removable SCSI
|
|
1</literal>. A multitude of firmware revisions exist for this
|
|
drive. Your drive may report different numbers (e.g
|
|
<literal>21247 -005</literal>.</para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 150/250MB. Both 150MB (DC6150) and 250MB
|
|
(DC6250) tapes have the recording format. The 250MB tapes are
|
|
approximately 67% longer than the 150MB tapes. This drive can
|
|
read 120MB tapes as well. It can not write 120MB tapes.</para>
|
|
|
|
<para>Data transfer rate is 100kB/s</para>
|
|
|
|
<para>This drive reads and writes DC6150 (150MB) and DC6250 (250MB)
|
|
tapes.</para>
|
|
|
|
<para>This drives quirks are known and pre-compiled into the SCSI
|
|
tape device driver (&man.st.4;).</para>
|
|
|
|
<para>Under FreeBSD 2.2-CURRENT, use <command>mt blocksize
|
|
512</command> to set the blocksize. (The particular drive had
|
|
firmware revision 21247 -005. Other firmware revisions may behave
|
|
differently) Previous versions of FreeBSD did not have this
|
|
problem.</para>
|
|
|
|
<para>Production of this drive has been discontinued.</para>
|
|
|
|
<para>Reported by: Pedro A M Vazquez
|
|
<email>vazquez@IQM.Unicamp.BR</email></para>
|
|
|
|
<para>&a.msmith;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-viper2525">
|
|
<title>Archive Viper 2525</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>ARCHIVE
|
|
VIPER 2525 25462 -011</literal> <literal>type 1 removable SCSI
|
|
1</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 525MB.</para>
|
|
|
|
<para>Data transfer rate is 180kB/s at 90 inches/sec.</para>
|
|
|
|
<para>The drive reads QIC-525, QIC-150, QIC-120 and QIC-24 tapes.
|
|
Writes QIC-525, QIC-150, and QIC-120.</para>
|
|
|
|
<para>Firmware revisions prior to <literal>25462 -011</literal> are
|
|
bug ridden and will not function properly.</para>
|
|
|
|
<para>Production of this drive has been discontinued.</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-conner420r">
|
|
<title>Conner 420R</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>Conner
|
|
tape</literal>.</para>
|
|
|
|
<para>This is a floppy controller, mini cartridge tape drive.</para>
|
|
|
|
<para>Native capacity is XXXX</para>
|
|
|
|
<para>Data transfer rate is XXX</para>
|
|
|
|
<para>The drive uses QIC-80 tape cartridges.</para>
|
|
|
|
<para>Reported by: Mark Hannon
|
|
<email>mark@seeware.DIALix.oz.au</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-ctms3200">
|
|
<title>Conner CTMS 3200</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>CONNER
|
|
CTMS 3200 7.00</literal> <literal>type 1 removable SCSI
|
|
2</literal>.</para>
|
|
|
|
<para>This is a mini cartridge tape drive.</para>
|
|
|
|
<para>Native capacity is XXXX</para>
|
|
|
|
<para>Data transfer rate is XXX</para>
|
|
|
|
<para>The drive uses QIC-3080 tape cartridges.</para>
|
|
|
|
<para>Reported by: Thomas S. Traylor
|
|
<email>tst@titan.cs.mci.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-dectz87">
|
|
<title><ulink
|
|
url="http://www.digital.com/info/Customer-Update/931206004.txt.html">DEC TZ87</ulink></title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>DEC
|
|
TZ87 (C) DEC 9206</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>density code 0x19</literal></para>
|
|
|
|
<para>This is a DLT tape drive.</para>
|
|
|
|
<para>Native capacity is 10GB.</para>
|
|
|
|
<para>This drive supports hardware data compression.</para>
|
|
|
|
<para>Data transfer rate is 1.2MB/s.</para>
|
|
|
|
<para>This drive is identical to the Quantum DLT2000. The drive
|
|
firmware can be set to emulate several well-known drives,
|
|
including an Exabyte 8mm drive.</para>
|
|
|
|
<para>Reported by: &a.wilko;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-exb2501">
|
|
<title><ulink
|
|
url="http://www.Exabyte.COM:80/Products/Minicartridge/2501/Rfeatures.html">Exabyte EXB-2501</ulink></title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>EXABYTE
|
|
EXB-2501</literal></para>
|
|
|
|
<para>This is a mini-cartridge tape drive.</para>
|
|
|
|
<para>Native capacity is 1GB when using MC3000XL
|
|
mini cartridges.</para>
|
|
|
|
<para>Data transfer rate is XXX</para>
|
|
|
|
<para>This drive can read and write DC2300 (550MB), DC2750 (750MB),
|
|
MC3000 (750MB), and MC3000XL (1GB) mini cartridges.</para>
|
|
|
|
<para>WARNING: This drive does not meet the SCSI-2 specifications.
|
|
The drive locks up completely in response to a SCSI MODE_SELECT
|
|
command unless there is a formatted tape in the drive. Before
|
|
using this drive, set the tape blocksize with</para>
|
|
|
|
<screen>&prompt.root; <userinput>mt -f /dev/st0ctl.0 blocksize 1024</userinput></screen>
|
|
|
|
<para>Before using a mini cartridge for the first time, the
|
|
mini cartridge must be formated. FreeBSD 2.1.0-RELEASE and
|
|
earlier:</para>
|
|
|
|
<screen>&prompt.root; <userinput>/sbin/scsi -f /dev/rst0.ctl -s 600 -c "4 0 0 0 0 0"</userinput></screen>
|
|
|
|
<para>(Alternatively, fetch a copy of the
|
|
<command>scsiformat</command> shell script from FreeBSD
|
|
2.1.5/2.2.) FreeBSD 2.1.5 and later:</para>
|
|
|
|
<screen>&prompt.root; <userinput>/sbin/scsiformat -q -w /dev/rst0.ctl</userinput></screen>
|
|
|
|
<para>Right now, this drive cannot really be recommended for
|
|
FreeBSD.</para>
|
|
|
|
<para>Reported by: Bob Beaulieu
|
|
<email>ez@eztravel.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-exb8200">
|
|
<title>Exabyte EXB-8200</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>EXABYTE
|
|
EXB-8200 252X</literal> <literal>type 1 removable SCSI
|
|
1</literal></para>
|
|
|
|
<para>This is an 8mm tape drive.</para>
|
|
|
|
<para>Native capacity is 2.3GB.</para>
|
|
|
|
<para>Data transfer rate is 270kB/s.</para>
|
|
|
|
<para>This drive is fairly slow in responding to the SCSI bus during
|
|
boot. A custom kernel may be required (set SCSI_DELAY to 10
|
|
seconds).</para>
|
|
|
|
<para>There are a large number of firmware configurations for this
|
|
drive, some have been customized to a particular vendor's
|
|
hardware. The firmware can be changed via EPROM
|
|
replacement.</para>
|
|
|
|
<para>Production of this drive has been discontinued.</para>
|
|
|
|
<para>Reported by: &a.msmith;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-exb8500">
|
|
<title>Exabyte EXB-8500</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>EXABYTE
|
|
EXB-8500-85Qanx0 0415</literal> <literal>type 1 removable SCSI
|
|
2</literal></para>
|
|
|
|
<para>This is an 8mm tape drive.</para>
|
|
|
|
<para>Native capacity is 5GB.</para>
|
|
|
|
<para>Data transfer rate is 300kB/s.</para>
|
|
|
|
<para>Reported by: Greg Lehey <email>grog@lemis.de</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-exb8505">
|
|
<title><ulink
|
|
url="http://www.Exabyte.COM:80/Products/8mm/8505XL/Rfeatures.html">Exabyte EXB-8505</ulink></title>
|
|
|
|
<para>The boot message identifier for this drive is
|
|
<literal>EXABYTE EXB-85058SQANXR1 05B0</literal> <literal>type 1
|
|
removable SCSI 2</literal></para>
|
|
|
|
<para>This is an 8mm tape drive which supports compression, and is
|
|
upward compatible with the EXB-5200 and EXB-8500.</para>
|
|
|
|
<para>Native capacity is 5GB.</para>
|
|
|
|
<para>The drive supports hardware data compression.</para>
|
|
|
|
<para>Data transfer rate is 300kB/s.</para>
|
|
|
|
<para>Reported by: Glen Foster
|
|
<email>gfoster@gfoster.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp1533a">
|
|
<title>Hewlett-Packard HP C1533A</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>HP
|
|
C1533A 9503</literal> <literal>type 1 removable SCSI
|
|
2</literal>.</para>
|
|
|
|
<para>This is a DDS-2 tape drive. DDS-2 means hardware data
|
|
compression and narrower tracks for increased data
|
|
capacity.</para>
|
|
|
|
<para>Native capacity is 4GB when using 120m tapes. This drive
|
|
supports hardware data compression.</para>
|
|
|
|
<para>Data transfer rate is 510kB/s.</para>
|
|
|
|
<para>This drive is used in Hewlett-Packard's SureStore 6000eU and
|
|
6000i tape drives and C1533A DDS-2 DAT drive.</para>
|
|
|
|
<para>The drive has a block of 8 dip switches. The proper settings
|
|
for FreeBSD are: 1 ON; 2 ON; 3 OFF; 4 ON; 5 ON; 6 ON; 7 ON; 8
|
|
ON.</para>
|
|
|
|
<informaltable frame="none" pgwide="1">
|
|
<tgroup cols="3">
|
|
<thead>
|
|
<row>
|
|
<entry>switch 1</entry>
|
|
<entry>switch 2</entry>
|
|
<entry>Result</entry>
|
|
</row>
|
|
</thead>
|
|
|
|
<tbody>
|
|
<row>
|
|
<entry>On</entry>
|
|
<entry>On</entry>
|
|
<entry>Compression enabled at power-on, with host
|
|
control</entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>On</entry>
|
|
<entry>Off</entry>
|
|
<entry>Compression enabled at power-on, no host
|
|
control</entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>Off</entry>
|
|
<entry>On</entry>
|
|
<entry>Compression disabled at power-on, with host
|
|
control</entry>
|
|
</row>
|
|
|
|
<row>
|
|
<entry>Off</entry>
|
|
<entry>Off</entry>
|
|
<entry>Compression disabled at power-on, no host
|
|
control</entry>
|
|
</row>
|
|
</tbody>
|
|
</tgroup>
|
|
</informaltable>
|
|
|
|
<para>Switch 3 controls MRS (Media Recognition System). MRS tapes
|
|
have stripes on the transparent leader. These identify the tape
|
|
as DDS (Digital Data Storage) grade media. Tapes that do not have
|
|
the stripes will be treated as write-protected. Switch 3 OFF
|
|
enables MRS. Switch 3 ON disables MRS.</para>
|
|
|
|
<para>See <ulink url="http://www.hp.com/tape/c_intro.html">HP
|
|
SureStore Tape Products</ulink> and <ulink
|
|
url="http://www.impediment.com/hp/hp_technical.html">Hewlett-Packard
|
|
Disk and Tape Technical Information</ulink> for more information
|
|
on configuring this drive.</para>
|
|
|
|
<para><emphasis>Warning:</emphasis> Quality control on these drives
|
|
varies greatly. One FreeBSD core-team member has returned 2 of
|
|
these drives. Neither lasted more than 5 months.</para>
|
|
|
|
<para>Reported by: &a.se;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp1534a">
|
|
<title>Hewlett-Packard HP 1534A</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>HP
|
|
HP35470A T503</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>Sequential-Access density code 0x13,
|
|
variable blocks</literal>.</para>
|
|
|
|
<para>This is a DDS-1 tape drive. DDS-1 is the original DAT tape
|
|
format.</para>
|
|
|
|
<para>Native capacity is 2GB when using 90m tapes.</para>
|
|
|
|
<para>Data transfer rate is 183kB/s.</para>
|
|
|
|
<para>The same mechanism is used in Hewlett-Packard's SureStore
|
|
<ulink url="http://www.dmo.hp.com/tape/sst2000.htm">2000i</ulink>
|
|
tape drive, C35470A DDS format DAT drive, C1534A DDS format DAT
|
|
drive and HP C1536A DDS format DAT drive.</para>
|
|
|
|
<para>The HP C1534A DDS format DAT drive has two indicator lights,
|
|
one green and one amber. The green one indicates tape action:
|
|
slow flash during load, steady when loaded, fast flash during
|
|
read/write operations. The amber one indicates warnings: slow
|
|
flash when cleaning is required or tape is nearing the end of its
|
|
useful life, steady indicates an hard fault. (factory service
|
|
required?)</para>
|
|
|
|
<para>Reported by Gary Crutcher
|
|
<email>gcrutchr@nightflight.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp1553a">
|
|
<title>Hewlett-Packard HP C1553A Autoloading DDS2</title>
|
|
|
|
<para>The boot message identifier for this drive is "".</para>
|
|
|
|
<para>This is a DDS-2 tape drive with a tape changer. DDS-2 means
|
|
hardware data compression and narrower tracks for increased data
|
|
capacity.</para>
|
|
|
|
<para>Native capacity is 24GB when using 120m tapes. This drive
|
|
supports hardware data compression.</para>
|
|
|
|
<para>Data transfer rate is 510kB/s (native).</para>
|
|
|
|
<para>This drive is used in Hewlett-Packard's SureStore <ulink
|
|
url="http://www.dmo.hp.com/tape/sst12000.htm">12000e</ulink>
|
|
tape drive.</para>
|
|
|
|
<para>The drive has two selectors on the rear panel. The selector
|
|
closer to the fan is SCSI id. The other selector should be set to
|
|
7.</para>
|
|
|
|
<para>There are four internal switches. These should be set: 1 ON;
|
|
2 ON; 3 ON; 4 OFF.</para>
|
|
|
|
<para>At present the kernel drivers do not automatically change
|
|
tapes at the end of a volume. This shell script can be used to
|
|
change tapes:</para>
|
|
|
|
<programlisting>#!/bin/sh
|
|
PATH="/sbin:/usr/sbin:/bin:/usr/bin"; export PATH
|
|
|
|
usage()
|
|
{
|
|
echo "Usage: dds_changer [123456ne] raw-device-name
|
|
echo "1..6 = Select cartridge"
|
|
echo "next cartridge"
|
|
echo "eject magazine"
|
|
exit 2
|
|
}
|
|
|
|
if [ $# -ne 2 ] ; then
|
|
usage
|
|
fi
|
|
|
|
cdb3=0
|
|
cdb4=0
|
|
cdb5=0
|
|
|
|
case $1 in
|
|
[123456])
|
|
cdb3=$1
|
|
cdb4=1
|
|
;;
|
|
n)
|
|
;;
|
|
e)
|
|
cdb5=0x80
|
|
;;
|
|
?)
|
|
usage
|
|
;;
|
|
esac
|
|
|
|
scsi -f $2 -s 100 -c "1b 0 0 $cdb3 $cdb4 $cdb5"</programlisting>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp35450a">
|
|
<title>Hewlett-Packard HP 35450A</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>HP
|
|
HP35450A -A C620</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>Sequential-Access density code
|
|
0x13</literal></para>
|
|
|
|
<para>This is a DDS-1 tape drive. DDS-1 is the original DAT tape
|
|
format.</para>
|
|
|
|
<para>Native capacity is 1.2GB.</para>
|
|
|
|
<para>Data transfer rate is 160kB/s.</para>
|
|
|
|
<para>Reported by: Mark Thompson
|
|
<email>mark.a.thompson@pobox.com</email></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp35470a">
|
|
<title>Hewlett-Packard HP 35470A</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>HP
|
|
HP35470A 9 09</literal> <literal>type 1 removable SCSI
|
|
2</literal></para>
|
|
|
|
<para>This is a DDS-1 tape drive. DDS-1 is the original DAT tape
|
|
format.</para>
|
|
|
|
<para>Native capacity is 2GB when using 90m tapes.</para>
|
|
|
|
<para>Data transfer rate is 183kB/s.</para>
|
|
|
|
<para>The same mechanism is used in Hewlett-Packard's SureStore
|
|
<ulink url="http://www.dmo.hp.com/tape/sst2000.htm">2000i</ulink>
|
|
tape drive, C35470A DDS format DAT drive, C1534A DDS format DAT
|
|
drive, and HP C1536A DDS format DAT drive.</para>
|
|
|
|
<para><emphasis>Warning:</emphasis> Quality control on these drives
|
|
varies greatly. One FreeBSD core-team member has returned 5 of
|
|
these drives. None lasted more than 9 months.</para>
|
|
|
|
<para>Reported by: David Dawes
|
|
<email>dawes@rf900.physics.usyd.edu.au</email> (9 09)</para>
|
|
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-hp35480a">
|
|
<title>Hewlett-Packard HP 35480A</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>HP
|
|
HP35480A 1009</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>Sequential-Access density code
|
|
0x13</literal>.</para>
|
|
|
|
<para>This is a DDS-DC tape drive. DDS-DC is DDS-1 with hardware
|
|
data compression. DDS-1 is the original DAT tape format.</para>
|
|
|
|
<para>Native capacity is 2GB when using 90m tapes. It cannot handle
|
|
120m tapes. This drive supports hardware data compression.
|
|
Please refer to the section on <link
|
|
linkend="hw-storage-hp1533a">HP C1533A</link> for the proper
|
|
switch settings.</para>
|
|
|
|
<para>Data transfer rate is 183kB/s.</para>
|
|
|
|
<para>This drive is used in Hewlett-Packard's SureStore <ulink
|
|
url="http://www.dmo.hp.com/tape/sst5000.htm">5000eU</ulink> and
|
|
<ulink url="http://www.dmo.hp.com/tape/sst5000.htm">5000i</ulink>
|
|
tape drives and C35480A DDS format DAT drive..</para>
|
|
|
|
<para>This drive will occasionally hang during a tape eject
|
|
operation (<command>mt offline</command>). Pressing the front
|
|
panel button will eject the tape and bring the tape drive back to
|
|
life.</para>
|
|
|
|
<para>WARNING: HP 35480-03110 only. On at least two occasions this
|
|
tape drive when used with FreeBSD 2.1.0, an IBM Server 320 and an
|
|
2940W SCSI controller resulted in all SCSI disk partitions being
|
|
lost. The problem has not be analyzed or resolved at this
|
|
time.</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-sdt5000">
|
|
<title><ulink
|
|
url="http://www.sel.sony.com/SEL/ccpg/storage/tape/t5000.html">Sony SDT-5000</ulink></title>
|
|
|
|
<para>There are at least two significantly different models: one is
|
|
a DDS-1 and the other DDS-2. The DDS-1 version is
|
|
<literal>SDT-5000 3.02</literal>. The DDS-2 version is
|
|
<literal>SONY SDT-5000 327M</literal>. The DDS-2 version has a 1MB
|
|
cache. This cache is able to keep the tape streaming in almost
|
|
any circumstances.</para>
|
|
|
|
<para>The boot message identifier for this drive is <literal>SONY
|
|
SDT-5000 3.02</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>Sequential-Access density code
|
|
0x13</literal></para>
|
|
|
|
<para>Native capacity is 4GB when using 120m tapes. This drive
|
|
supports hardware data compression.</para>
|
|
|
|
<para>Data transfer rate is depends upon the model or the drive. The
|
|
rate is 630kB/s for the <literal>SONY SDT-5000 327M</literal>
|
|
while compressing the data. For the <literal>SONY SDT-5000
|
|
3.02</literal>, the data transfer rate is 225kB/s.</para>
|
|
|
|
<para>In order to get this drive to stream, set the blocksize to 512
|
|
bytes (<command>mt blocksize 512</command>) reported by Kenneth
|
|
Merry <email>ken@ulc199.residence.gatech.edu</email>.</para>
|
|
|
|
<para><literal>SONY SDT-5000 327M</literal> information reported by
|
|
Charles Henrich <email>henrich@msu.edu</email>.</para>
|
|
|
|
<para>Reported by: &a.jmz;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-tandberg3600">
|
|
<title>Tandberg TDC 3600</title>
|
|
|
|
<para>The boot message identifier for this drive is
|
|
<literal>TANDBERG TDC 3600 =08:</literal> <literal>type 1
|
|
removable SCSI 2</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 150/250MB.</para>
|
|
|
|
<para>This drive has quirks which are known and work around code is
|
|
present in the SCSI tape device driver (&man.st.4;).
|
|
Upgrading the firmware to XXX version will fix the quirks and
|
|
provide SCSI 2 capabilities.</para>
|
|
|
|
<para>Data transfer rate is 80kB/s.</para>
|
|
|
|
<para>IBM and Emerald units will not work. Replacing the firmware
|
|
EPROM of these units will solve the problem.</para>
|
|
|
|
<para>Reported by: &a.msmith;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-tandberg3620">
|
|
<title>Tandberg TDC 3620</title>
|
|
|
|
<para>This is very similar to the <link
|
|
linkend="hw-storage-tandberg3600">Tandberg TDC 3600</link>
|
|
drive.</para>
|
|
|
|
<para>Reported by: &a.joerg;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-tandberg3800">
|
|
<title>Tandberg TDC 3800</title>
|
|
|
|
<para>The boot message identifier for this drive is
|
|
<literal>TANDBERG TDC 3800 =04Y</literal> <literal>Removable
|
|
Sequential Access SCSI-2 device</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 525MB.</para>
|
|
|
|
<para>Reported by: &a.jhs;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-tandberg4222">
|
|
<title>Tandberg TDC 4222</title>
|
|
|
|
<para>The boot message identifier for this drive is
|
|
<literal>TANDBERG TDC 4222 =07</literal> <literal>type 1 removable
|
|
SCSI 2</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 2.5GB. The drive will read all cartridges
|
|
from the 60 MB (DC600A) upwards, and write 150 MB (DC6150)
|
|
upwards. Hardware compression is optionally supported for the 2.5
|
|
GB cartridges.</para>
|
|
|
|
<para>This drives quirks are known and pre-compiled into the SCSI
|
|
tape device driver (&man.st.4;) beginning with FreeBSD
|
|
2.2-CURRENT. For previous versions of FreeBSD, use
|
|
<command>mt</command> to read one block from the tape, rewind the
|
|
tape, and then execute the backup program (<command>mt fsr 1; mt
|
|
rewind; dump ...</command>)</para>
|
|
|
|
<para>Data transfer rate is 600kB/s (vendor claim with compression),
|
|
350 KB/s can even be reached in start/stop mode. The rate
|
|
decreases for smaller cartridges.</para>
|
|
|
|
<para>Reported by: &a.joerg;</para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-wangtek5525es">
|
|
<title>Wangtek 5525ES</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>WANGTEK
|
|
5525ES SCSI REV7 3R1</literal> <literal>type 1 removable SCSI
|
|
1</literal> <literal>density code 0x11, 1024-byte
|
|
blocks</literal></para>
|
|
|
|
<para>This is a QIC tape drive.</para>
|
|
|
|
<para>Native capacity is 525MB.</para>
|
|
|
|
<para>Data transfer rate is 180kB/s.</para>
|
|
|
|
<para>The drive reads 60, 120, 150, and 525MB tapes. The drive will
|
|
not write 60MB (DC600 cartridge) tapes. In order to overwrite 120
|
|
and 150 tapes reliably, first erase (<command>mt erase</command>)
|
|
the tape. 120 and 150 tapes used a wider track (fewer tracks per
|
|
tape) than 525MB tapes. The <quote>extra</quote> width of the
|
|
previous tracks is not overwritten, as a result the new data lies
|
|
in a band surrounded on both sides by the previous data unless the
|
|
tape have been erased.</para>
|
|
|
|
<para>This drives quirks are known and pre-compiled into the SCSI
|
|
tape device driver (&man.st.4;).</para>
|
|
|
|
<para>Other firmware revisions that are known to work are:
|
|
M75D</para>
|
|
|
|
<para>Reported by: Marc van Kempen <email>marc@bowtie.nl</email>
|
|
<literal>REV73R1</literal> Andrew Gordon
|
|
<email>Andrew.Gordon@net-tel.co.uk</email>
|
|
<literal>M75D</literal></para>
|
|
</sect3>
|
|
|
|
<sect3 id="hw-storage-wangtek6200">
|
|
<title>Wangtek 6200</title>
|
|
|
|
<para>The boot message identifier for this drive is <literal>WANGTEK
|
|
6200-HS 4B18</literal> <literal>type 1 removable SCSI
|
|
2</literal> <literal>Sequential-Access density code
|
|
0x13</literal></para>
|
|
|
|
<para>This is a DDS-1 tape drive.</para>
|
|
|
|
<para>Native capacity is 2GB using 90m tapes.</para>
|
|
|
|
<para>Data transfer rate is 150kB/s.</para>
|
|
|
|
<para>Reported by: Tony Kimball <email>alk@Think.COM</email></para>
|
|
</sect3>
|
|
</sect2>
|
|
|
|
<sect2>
|
|
<title>* Problem drives</title>
|
|
|
|
<para></para>
|
|
</sect2>
|
|
</sect1>
|
|
|
|
<sect1>
|
|
<title>CDROM drives</title>
|
|
|
|
<para><emphasis>Contributed by &a.obrien;. 23 November
|
|
1997.</emphasis></para>
|
|
|
|
<para>Generally speaking those in <emphasis>The FreeBSD
|
|
Project</emphasis> prefer SCSI CDROM drives over IDE CDROM
|
|
drives. However not all SCSI CDROM drives are equal. Some
|
|
feel the quality of some SCSI CDROM drives have been
|
|
deteriorating to that of IDE CDROM drives. Toshiba used to be
|
|
the favored stand-by, but many on the SCSI mailing list have
|
|
found displeasure with the 12x speed XM-5701TA as its volume
|
|
(when playing audio CDROMs) is not controllable by the various
|
|
audio player software.</para>
|
|
|
|
<para>Another area where SCSI CDROM manufacturers are cutting corners is
|
|
adherence to the <link linkend="scsi-further-reading">SCSI
|
|
specification</link>. Many SCSI CDROMs will respond to <link
|
|
linkend="scsi-rogue-devices">multiple LUNs</link> for its target
|
|
address. Known violators include the 6x Teac CD-56S 1.0D.</para>
|
|
</sect1>
|
|
|
|
</article>
|